Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Background: We use NRF52 chip along with SDK 12.1.0. Since we have a few components of firmware (i.e. secure DFU settings, secure DFU , application, Softdevice) that go into...
The aim is to use the nRF51822 chip beside the application processor and to run the soft device S130 in it but as I saw, the newest SDK v12 supports only S132 Connectivity...
I am trying to update my S132v2.0.1 devices over the air to S132v3.0.0 and am getting no bootup, even after swapping dfu_dual_bank.c from the answer below.
devzone.nordicsemi...
I am studying this tutorial: nRF52 Online Power Profiler . I know this tutorial basically related to the ble_app_pwr_profiling example in the SDK: Power Profiling Application...
Hi, Nordic
I know pipe0 and pipe1 are be enabled on nRF24LU1 nRFgo SDK example for default PRX.
Now I only to enable pipe0, disable pipe1.
First, I use this...
Hi, Nordic engineer
nRF52832 as ESB PTX, nRF24LU1 as ESB PRX
same channel, crc, and match address and pipes, but from nRF52832 uart log, ESB TX fail event always show...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hello everyone~
Although one TWIM interface of the nRF52832 can "interconnect up to 127 individually addressable devices", I still think that use different interface will...
Hello everybody.
I'm trying to modify the original firmware that comes with the nRF51822 to make it sweep all of the permitted levels of transmission power.
I was able...
Hello,
I want to read the temperature value continuously on mobile scanner app. I implemented the program as stated in BLE Characteristics beginner tutorial and I am using...
Hey guys,
I’m trying to come up with a way to know if an advertisement was received via BLE_GAP_EVT_SCAN_REQ_REPORT, but then not actually send the SCAN response. It’s...
Iam using softdivice 110 and sdk 10.0.0, iam using spi driver for interfacing with spi slave device(flash memory device). I need to send command and then receive the data...
Hi,
I am trying to implement an ECG measurement device. nRF52832 collects the sensor value through SPI and send it to smartphone using ble_app_uart code. I need to send...
as sd132v3.0.0 got some Exciting functions.
I tried to use in my production.
everything work fine, except for dfu.
Trouble is:
when i upgrade from softdevice 2.0.1...
