Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hello,
I need to read the unique serial number from a nordic NRF 52832 device. This number is necessary for our production testing.
I have the latest SDK.
Thanks!
Hello
I have a custom board based on nrf9160 and I cannot claim and make REST API and JWT auth work for it.
These are the steps I followed
1. https://github.com/nRFCloud...
Hello,
I am facing an issue building the Matter light switch example for nRF5340 for ncs 2.8.0.
Include zboss_api.h is not working in zb_nrf_pwr_mgmt.c
Setup ...
I use nsc 2.3.0, nrf5340dk_nrf5340_cpuapp. I want to use nrf_rpc for communication between cores.
Enabling net core log causes endpoint bond timeout. Error sample attached...
Hi,
My nRF5340 board is PCA10095 2.0.2 2024.08. I'm using nRF connect for Desktip v5.1.0.
In the Qucik Start, it's successful to program Hello World example. But failed...
Hi,
I'm a little disoriented. I used to set the tx power configuration for the nRF5340:
in the file <prjdir>\child_image\hci_rpmsg.conf.
How and where can I set the...
Hi All,
I am using ' NRF SDK v2.7 + NRF5340 DK + VSCode ' and cloned a official nrf ' matter light bulb ' sample.
My question is the default 'matter light bulb' uses NRF5340...
Hi,
we had used nRF52832 in our product. Our product is undergoing FCC & IC certification.
FCC & IC regulatory body had requested to provide Tone of tolerance (Power)...
Hi, I started my project with SDK version 2.6.1 (starting from the 'hello_world' example). I added mcuboot (CONFIG_BOOTLOADER_MCUBOOT=y). I followed the instructions in the...
Use nrf_modem_lib_init() to initialize the modem, followed by lte_lc_connect() to connect to LTE. However, it consistently fails to connect to LTE. After it times out, the...
HW: 52840DK PCA10056 3.0.1 2023.16
NCS SDK: v2.8.0
I want to test Zephyr's BLE controller instead of the default SoftDevice controller, and the `prj.conf` of ISO_CENTRAL...
Hello.
I am trying to use nRF Connect SDK v2.8.0 and nRF52840 to run Matter's Light Switch and Light Bulb.
I was able to confirm that it works with nRF52840-DK, but...
Hi there,
Our firmware is built on NCS 2.6.1 (soon to be ported to 2.7.0) and uses MCUboot.
I want to set REGOUT0 to 5 (which corresponds to 3.3V) and the `nrfjprog -...
I am trying to upgrade my project which is previously build with NRF connect SDK 2.6.1 to 2.8.0
I am getting this error while building
warning: NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Greetings,
when trying to compile simple GPIO configuration for NRF5340, the compile fails with:
In file included from C:/Apps/NordicSemiconductor/SDKs/v2.7.0/zephyr/include...
