Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi Support Team
Our project need 8mA charge current, how to configure charge current of nPM1300 to 8mA？ Or could you provides us other nPM chip or solution that can meet...
Hi all,
I have a custom board running on nrf9161. I need to flash the custom board with the NRF9160-DK. But I am running into some issues. the development is at early stages...
Hi,
I'm trying to add a manufacturing specific attribute to the On/Off cluster.
To do this I have so far created a custom attribute list with ZB_ZCL_DECLARE_ON_OFF_ATTRIB_LIST_CUSTOM...
Hi NordicTeam
i am working with the Mesh Dimming server example out of the SDK MESH 5.0.0.
While investigation the Packet loss in my prevous ticket i was wondering if...
Hi,
Working with the NRF5340-nrf7002 and the W25Q16RV flash memory in our project.
Initially, I configured an 8MB( W25Q64RV) external flash without issues and tested...
I've been testing the FMDN locator tag sample application with a nRF52840 devkit and I would very much like to get an answer to the following questions:
1. Is it possible...
Hi, I'm having an issue with the bt_mesh_resume() function in my project based on Zephyr and Bluetooth Mesh. My code is trying to cycle the Mesh network on and off to save...
Greetings
I have been going through the BLE fundamentals course, and I am currently on Lesson 4 exercise 1, which entails creating custom services. I have went through the...
I am working with nRF Connect SDK 2.6.1 on a Central and a Peripheral and I am running the BAP similar to the nRF Audio Example. I am using out of band pairing over UART for...
Hi,
I am working on application code for the nrf9160. Current NCS version is 1.5.1, although I do not think my ancient NCS version is relevant to this issue.
I have removed...
I can't find any documentation on how you are supposed to define partitions in NCS 2.7 when using MCUboot. Previously Partition Manager was responsible for this and was overriding...
Hi,
We have a few questions regarding NRF52832 and NRF52833, please support to clarify for us.
1. Does NRF52832 support Bluetooth 5.4 or 5.3?
2. Does NRF52833 support...
Hii,
I´m working with LTE IoT 4 Click, by Mikroe, that use a nrf9160.
I need to connect to network with my modem, but i have some erros. My goal is to communicate with...
...On a NRF5340, using NRF Connect 2.6.1 SDK and tool chain.
In our application, we need to select if NRF5340 device boots in ZIGBEE ROUTER role or ZIGBEE END DEVICE role...
I've written a custom manufacturing programming tool for ARM Cortex-M4 nRF52832 and nRF52810 devices. It uses a J-Link Plus USB programmer (J-Link V7.98g) and is implemented...
