Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Hi,
I am working on a smartwatch PoC using the nRF7002 DK (nRF5340), and I am trying to interface a 1.8" ST7735 SPI TFT display (128x160).
Hardware: - Board: nRF7002DK...
Ultrasonic welding is commonly used to seal plastic enclosures for electronic devices. 32kHz crystals can be damaged by this type of welding and manufacturers recommend not...
Does APPROTECT supersede SECUREAPPROTECT or do both need to be enabled for maximum security?
Similarly, do the HW protections (APPROTECT, SECUREAPPROTECT, ERASEPROTECT)...
I am trying to measure current on a nRF52 DK v3.0.0 using PPK II in source mode.
I cut SB9 and soldered SB12 as described in this guide: https://docs.nordicsemi.com/bundle...
Hello , I 'm trying to use the Lan865x (two -wire eth click ) chip with the nrf52840dk board , using zephyr 3 . 7 . I 'm getting always this error while trying a net sample...
Hello!
I've been trying some of the solutions around these forums but I can't seem to get my nRF52840 DK to show up on my device manager so I'm unable to flash anything...
NCS 2.7.0, NRF52840, SYSBUILD with MCUBOOT
We have 1 specific board which is failing with a hardfault and assert MPSL ASSERT: 112, 1617 it occurs whenever we activate...
Hello Nordic Team,
I am using nRF Connect SDK v2.9.0 with the nRF52833 controller. I am currently working on OTA implementation.
I am implementing OTA in another code...
I want to prototype an Auracast transmitter, with an analogue audio input, which is also WiFi enabled. I have read that the recommendation to get started with the nrf5340...
i'm measuring approximately 1.5uA (at 3V3) when sleeping between BLE advertising events, using a program based on one of your the standard examples.... as an experiment, i...
There expect to be a physical limit to the number of components an AHB can support.
For instance, if 8 different masters (Including App core, Net core, several peripherals...
Hi Dev,
Development platform: NRF54L15 + NCS 3.2.3. We are using the GRTC SYSCOUNTER as a system timestamp. Under normal conditions, a software reset does not clear the...
As the title, I have already tested the ESB routine (esb ptx Sample/esb prx Sample) by using nRF54LM20-DK + nRF54L15-DK. There was absolutely no problem. But when I added...
Hello,
I have a project in Visual studio code and Nrf connect.
MCU is a NRF 52833.
For the certicications, the lab request me the DTM mode.
I tried the use the Sample...
