I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello,
I am looking for a low latency (end to end) wireless module for Joystick application and this is for a medical VR platform.
Latency requirement is <= 5ms.
Data...
Hi I'm new on zephyr
In my hardware the sensors around the soc are most of time not powered.
At Startup the OS initialise SPI, I2C, UART and some pins are set to 1....
Hi,
I am working on nrf52832, s132, SDK17, trying to trigger the saadc with the RTC2
This is my setup :
what I am trying to do is to periodically trigger a series...
I am using a custom board using the nRF52832. I have developed a number of applications using this board sucessfully using nRF5 SDK.,
I am porting a current application...
Project Zip:
Following is my setup:
Board : NRF52832 by Sparkfun( Link ) - Added pull-up resistor for TWI
Sensor: LIS2DH12(Custom breakout)
IDE: Segger Studio...
https://devzone.nordicsemi.com/f/nordic-q-a/79832/need-interface-mcu-initial-boot-firmware
apparently i can't update it anymore. does 'engineer assigned' mean that it can...
Hello,
I was measuring the current of a circuit I made using a PPK II and noticed I am getting two different readings from the two PCs I used (a work and a home PC).
Both...
hi
my first test do not run, bletooth is not enabled and could not get the bluetooth device led on board and signal on my mobile.
i following this link
https://infocenter...
Dear team,
i am working on ble_app_lbs_nus_c project when in this project try to add nrfx_timer.c file
we got an error like this.
and in sdk_config.h file is there ...
Hi,
I am receiving NRF9160 board. Please let me know if we need to change anything to support India Bands. Also it will be great if you can share Indian service provider...
How do I quickly check if the external crystal (32.768 with 15pf load caps.) I soldered is working.
I built a custom board but had to reflow solder in my lab.
Everything...
Dear DevZone community,
I'm developing a Mesh application using nRF52840 Segger Embedded Studio (SES) onLinux. I'm using version 5.0.0 of the Mesh SDK. As desccribed in...
Hi all, I have integrated a slightly customised Ble to Uart example with the buttonless DFU implementation and libraries, and obviously its size inflated. I need to decrease...
Hi. I am trying to generate a shared key via ECDH to encrypt message through UART between nrf52832 and Qualcomm chip. nRF52832 is using uECC and Qualcomm is using openssl...
