Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
Hi What is the better way to add multiple generic on off element to light switch server application. currently planing to add seperate simple_on_off_server_t m_server_x and...
Hi~.
I have an inquiry about sleep and wake up of the nRF52840 in high voltage mode.
Hardware and power design configuration
I am trying to use high voltage mode by...
When the application is started I get the following error:
<error> peer_manager_pds: Could not initialize flash storage. fds_init() returned 0x860A. 00> 00> <error> peer_manager...
Hi there!
I have an SD card reader and ST7735 connected to an nRF52850 DK, both working fine. Furthermore, I 'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK...
Hello everybody,
I´m trying to add a custom service to the ble_app_buttonless_dfu example in sdk 17.0.2 . Therfore i increment the NRF_SDH_BLE_VS_UUID_COUNT but this results...
Hello, I´m using nRF52DK BLE module with ContikiNG and I seem to be having issues when trying to connect with the device using the mac address. I´m trying to setup the basic...
Dear all, I'm new on nordic and I have to combine a bootloader BLE+UART. I read some threads but I can't to combine UART + BLE. Can I have an help?
Thanks in advance
Hello,
I am trying to configure my own bootloader for DFU, i use the secure_bootloader_ble_s132 as an exemple for nrf52832 DK.
after i flash the softdevice, the app...
Has anyone done multiple mqtt client connections from an nrf9160? Is it simply a matter of using the mqtt api and defining multiple client structures with unique rx/tx buffers...
Im install nRF Connect SDK 1.5.1 trough nRF Connect 3.6.1 Desktop app to learn zephyr RTOS and switch from nrf5 SDK to it but there is some bug and "Configure nRF Connect...
Hello,
I just receive a PPK2 and looking at power usage/profile. Below is the captured profile when the application is run from the debugger and then detached. This captures...
Hello,
ncs1.5.0
As shown in the question,
I use rtc to generate a 1kHz square wave, and use an oscilloscope to measure only 964 Hz.
Is there a problem with where I...
Hi.
I am using the oberon crypto backend module to use LESC in the application firmware. (I referred to the GLS example)
And I am trying to add a boot loader to use DFU...
Hello all, we are trying to set up a project with a nRF52840 chip in combination with 2 Acconeer A111 sensors. So far I have worked with a nRF52840 development kit and the...
Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
