Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello, I am trying to do DFU over BLE for nrf52 devices from another microcontroller (ESP32 to be specific), I couldn't find any data or example code to do this, are there...
Hello,
I have developed an application for my NRF52 DK and I want to port it to an NRF52832-QFAB-R which has a reduced amount of storage. I have changed the parameter "Target...
Hi,
I am following then nRF Connect SDK Tutorial - Part 1 | NCS v1.4.0.
I am using nRF Connect SDK 1.4.99-dev (installed via the Toolchain Manager)
In part 1.3.2 Build...
I recently switched from 52832 development using IAR to 52833 development using SES. As a result, I downloaded all new versions of the SDK, softdevice and, of course, SES...
There is a marked improvement in the handling of TrustZone in nrfjprog 10.11.0 and 10.12.00, but it seems it's still not quite all the way there. I can do:
and am able...
Hello,
I am developing DFU over a custom IEEE802.15.4 Protocol in our own embedded OS. I managed to write the new Firmware starting at bank1_start address. Now I need to...
Hello,
I am using nRF connect SDK v1.4.99-dev1. I have imported ZigBee light_bulb, light_switch,network_coordinator project in SEGGER and successfully created
the Zigbee...
-I was following this link- " devzone.nordicsemi.com/.../" and installed SEGGER JLink.
(all on Ubuntu)
-Installed gcc-arm and changed the tool chain path on Makefile.posix...
I try DTM using the serialized application . The serialized application interface is UART.
The software on Connectivity board is ble_connectivity in nRF5 SDK , it is not...
nRF52832 and SDK 17.0.2
Using the Examples/crypto/nrf_crypto/aes/aes_all_cli example I am getting the wrong output in CFB mode.
"example key_size 256_bit"
"example aes...
I am working on nRF51-DK with nRF51422 with softdevice S130 and SDK 12.3.0.
I see that GPIOTE driver provides sensing for signal transitions like NRF_GPIOTE_POLARITY_LOTOHI...
Hi,
I have setup the Segger Embedded Studio for ARM (Nordic Edition) V5.10d, and managed to compile a sample app from ,
V1.4.2 -> nrf -> samples -> bluetooth -> peripheral...
Hello,
I have different behaviour with 2 identical boards.
They behave differently (at least for BLE functions).
With jlink interface, I saved the flash binary of...
I have installed the toolchain according to nRF Connect guideline, on my MAC OSX.
My option settings are listed in the attached image.
I downloaded release 1.4.2.
...
Hi Sir
We are developing a product with nRF5340,
Now we faced the PCB layout symbol creation issue,
I can't find any information about footprint of nRF5340,
Can someone...
