Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
hello,
We have a product in production using nRF51422 and we are scaling up volume in a new manufacturing facility.
The functional tester stations require use of Master...
Hi!
Is there an example of how to use BLE_GAP_CONN_SEC_SET_MODE_LESC_WITH_MITM?
I cannot find one and I am having a hard time understanding what I need to do to make...
Hi,
I'm trying to use the pc-ble-driver "nrf-ble-driver-4.1.1-win_x86_32" to communicate with our nRF52-based embedded product. The fact that the PC and embedded implementations...
Hi,
I am using NRF52832 with secure bootloader to OTA my application in the field using Dual Bank updates and everything is working fine. In my application, I am using FDS...
Hi,
I need to use external eeprom memory AT24C256. I have not found any example for nrf52, so I started with migration existing arduino code to Nordic´s. Here is the Arduino...
Hey,
I am working on NRF51822, S130 softdevice integrating security, I have used the GLS as a reference for security implementation.
I have a use case in which I am...
I have both ble_app_uart_c and ble_app_uart they are automatically connected to each other if they are on. my question is ble_app_uart_c supports one to many or not? if it...
I am developing using pc-ble-driver-js and nrf52840 dongle.
We know that nrf's development tools (nrf connect ...) are being developed using an electron framework,
and...
We are using SDK 15.2.0 and softdevice s132 v6.10. we want to use the concurrent feature for broadcaster and observer. we wanted to just confirm that this feature is reliable...
Hi, I don't understand enough about electrical, but i found that a little piece of component in my nRF52840 dongle was gone.
It was something in this position:
It was...
Hello,
I'm trying to measure execution time of a piece of code in nRF52832. I was searching and found that I need to get the start time and finish time by using
beginval...
Hi,
I am using nrf52840 Preview - DK, with SDK v15.3.0 and Softdevice API 6.1.1
As we need to set NRF_LOG by setting the NRF_LOG_ENABLE and NRF_LOG_BACKEND_URAT_ENABLE...
Hi,
currently, i'm developing nRF52832 chip and I trying to use two GATT services.
I want to know about that "Can I use my custom services with Nordic Uart Service"...
I am basically wondering what the difference between these two examples in the SDK are?
Also, I see in both cases after the spi_transfer is called there is the following...
