Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
we are using a custom board, with codes tested on a NRF52 DK. We reconfigured the pins and when using pin P0.09 (by default NFC) as an input "active_high" and with ...
Hello,
I've done this steps:
I erased the whole chip: nRFgo Studio/ DeviceManager/nRF5x Programming/Erase all
I programmed the Softdevice s132_nrf52_5.0.0_softdevice...
Hello Nordic Team,
i use SDK 12.3 and SoftDevice S130.
In the template project ( \examples\ble_peripheral\ble_app_template ), the BSP module is used to indicate advertising...
Hello,
For my project I need to send raw data (without prefix or timestamps ) along with system logs trough the same UART.
So far one possible solution is to use NRF_LOG_RAW_INFO...
I've been using nRF24LE1 for development. The HAL library provide the AES encryption for ECB mode. Now I need the decryption function. Does anyone has the realization? Any...
Hello everyone,
I use SDK14.2 and s132 softdevice. I can read "NRF_SAADC_INPUT_AIN0" and "NRF_SAADC_INPUT_VDD" pins and system is working properly.
Working Code like...
Dear friends,
I am using the nRF 52832, s132. I want to know the BER (bit error rate) of the BLE link. How can i measure it? Further, to what extent do other radio interferences...
Hi.
I want to know the time difference between functions by using a timer instead of a difference. I've looked at app_timer.h, but it's hard to understand.
I do not need...
I am trying to use the ADC to take power measurements on an interval. I found an example to read the values out online:
void ADC_IRQHandler() { nrf_adc_conversion_event_clean...
I am designing a PCB using the NRF52832 and this antenna . The antenna design guidelines suggest ground clearance and direct traces from the NRF52832 to the antenna without...
I am working on a project which I wish to Paer between to nRF51422 devices and to use the auto reconnect between them. there won't be any display so it must be automatically...
Hi,
is it necessary to use internal regulator for NFC DC/DC or we can use normal internal LDO in design.
also if we need to use internal DC/DC regulator, what is the...
Hi, I have tried to find a solution for some time now in the Nordic Semiconductor forms.
We have been noticing a peak or a disturbance in voltage in every connection interval...
