I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
According to the documentation, you should run azure_iot_hub_dps_reset() in order to force DPS registration again.
But if the device has previously been enrolled and a device...
1. What is the Bluetooth version in NCS 2.6.1?
2. How to get Bluetooth version from NCS? is there any variable? I cannot find it in the release note neither. https://docs...
Hello,
I am using nRF Connect SDK v2.9.0, and nRF54l15 board. I enabled the watchdog timer and used its driver in zephyr/drivers/watchdog.h
It seems to work fine. The...
I have checked the PWM library in the nRF Connect SDK, and it seems that the library does not support init and deinit functions. The function pwm_set_pulse_dt(&pwm_led, 0...
Hello,
I’m currently working with a custom board based on the nRF9160 SiP, and I would like to measure the LTE-M TX power after the antenna impedance matching circuit. Ideally...
I am using the nrf52840 chip on a custom made PCB that is powered by a USB-C which provides it with 5V.This 5V is then converted to 12V using CH224K which then is wired to...
Hi,
we have ESB PTX and PRX couple from nRF54H20 nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin build for CPURAD...
Using wireless sensors with nRF54L15, the sensors do not need to be connected, only broadcast a small amount of information. There will be 50-60 thousand nodes, and they are...
Hi, I'm trying to setup serial recovery in my project, in order to update firmware via USB cdc-acm.
I'm following this exercise from the academy which seems what I need...
Hello!
I am interested in the Non-IP Data Delivery support in the nRF9160 module. In the description of AT commands, I did not see an opportunity to set PDP-type="Non-IP...
We use a module like EC2832AA1. I checked that nRF52832-QFAA-R is used for this module. This module has ap-protect enabled. So I added the command "nrfjprog --recover" to...
Hello!
We have developed a product that we would like to add some testing for and I have looked at both ztest and unity testing. Currently I am struggling with running the...
I have tried using SMP svr example with MCUboot for FOTA, NRF Connect SDK version 2.9.0. The example is located in zephyr\samples\subsys\mgmt\mcumgr. This example is working...
Hi, I have develop a project nRF5340 + W5500 Ethernet IC
Last time I develop a code with nRF52840 + w5500 and work success, but this time the same code work with nRF5340...
