I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I have a packet that I am sending out using the nrf52840. Using another piece of code supplied by Emil Lenngren, information from the solar_sensor_beacon project and raw data...
Hi,
I am using the NRF52840 dongles for BLE communication with S140 and the NRF5 17.1.0 SDK. I have plugged each dongle in a Raspberry Pi 3B+, and have set the DCDC regulator...
Hi, We are developing a product which is reading RTDs and thermistors from the NRF52833's internal ADC. We're working on compensating for the intrinsic errors of the ADC and...
Hello,
In my device I have a nrf52840 which communicates with a STM32 via uart.
In my nrf52840 I use the MCUboot.
Is there any documentation or source code that would...
Hi all,
I am developing my own provisioner with the nrf52840 chip. My idea is to be able to add at least 2000 nodes to a bluetooth mesh network with the provisioner but...
Hi, I'm delevoping an appilcation which can generate one sample per 20 us (accomplished with timer0) and transmit one ESB packet when 20 samples are collected. Below is the...
I'm using NCS 2.7.0 and NCS 2.9.0 to read the BT stack version information on an nRF5340. See below for the results.
How should the fw_version, fw_revision, and fw_build...
Hello Nordic-team,
I´m currently developing an application which has been based on a 54L15DK an I´m using an overlay file for adjusting the ports to my own hardware. That...
I/ trying to read the ID of a Fijitsu FRAM type MB85RS4MT using the Nordic device nRF5340. I can properly initialize the SPI and transmit the RDID =0x9F command. The FRAM...
Hi,
I'm working on implementing a modem upload feature (using probe-rs) to be integrated into our production programming line.
Following the procedure described here ...
Hello,
I am trying to use the SAADC peripheral on my nrf5340dk without using the zephyr API; I am writing my program bare-metal. My goal is to set up the ADC in continuous...
Hi everyone,
I'm quite new to the Nrf Connect SDK and Zephyr.
I'm trying to implement a simple DFU (over UART) bootloader. The idea is that when the microcontroller powers...
Hello,
We have a water meter project that involves cellular and GPS functionalities, and we need to design the schematic. After reviewing the hardware design guidelines...
Running into a slight issue where the timebase for system (reference time + uptime aka k_uptime_ticks()) drifts relative to sensor sampling rates. Attempt to synchronize the...
Problem: Upgrading to newer SDK broke RTT processing of backspace character. Details: We had been using RTT with the v2.4.1 SDK (for our nRF52840 development) and yesterday...
