I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi,
I used the reference code from inter_less8_exer3_solution and successfully built it with the nrf5340dk board. However, when building it for the nrf7002dk , I encountered...
I'm using firmware 1.3.6 and sdk 2.7 for Nordic nRF9160. For the internet connection ppp is being used.
Here are the results:
modem shell:
time wget https://leil.de...
Hi,
as i would like to use the uart shell for production purposes as well (e.g. setting the devices serial number) - how can i turn off the shell at runtime (in order to...
Hi,
I've been working on building and flashing the OpenThread CLI sample in two setups:
Setup 1 : nRF21540DK
Setup 2 : nRF52840DK + nRF21540EK
While I've managed...
I've been working on building and flashing the OpenThread CLI sample in two setups:
Setup 1 : nRF21540DK
Setup 2 : nRF52840DK + nRF21540EK
I'm using NCS v2.6.1....
Is it possible for the nRF7002 to operate in both SoftAP and STA modes simultaneously?
From my understanding of the nrfwifi driver, it seems that this functionality may...
Hello
I'm working with the nRF21540 and the nRF Connect SDK 2.6.2.
I would like to set my TX Power to 20 dBm and also check this value. Currently my configuration looks...
Greetings,
I've been developing a DFU firmware that should update the device through Android. The thing is, the device works, but I changed the advertising name, and it...
Hi,
I'm using the nRF5340 Audio application under NCS v2.5.0 as Unicast client.
I want to use the GATT Caching feature on my application.
How should I implement it...
Hello.
There was a problem with high current consumption when using Antenna 2 in some products.
The failure rate seems to be less than 7%, and the current consumption...
Hello,
I want to combine BLE, ANT+ and Apple Find My in one project.
I have permission to use ANT+ and Apple Find My.
I ran the two examples separately and they worked...
I have noticed that the RESETREAS register does not accumulate flags even though the documentation says it should. " Unless cleared, the RESETREAS register will be cumulative...
I have recently purchased a nrf7002 EK from element14.
I have connected it to nrf5340DK board and tried flashing the Wifi-shell sample application(with the help of video...
I’m not sure if I’m posting in the right forum, but since the EVK-ANNA-B402 uses the nRF52833, I thought this might be the place for questions related to it.
Steps followed...
I am using the cdc_acm example and have added a command to set and read tx power. I am trying to use the following commands for this.
BT_HCI_OP_VS_WRITE_TX_POWER_LEVEL...
