Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi there,
This is actually a question re. the Android BLE library ( https://github.com/NordicSemiconductor/Android-BLE-Library ), so please re-direct me if necessary.
...
Hi all,
maybe a dumb question, but here to listen any advice. I am using nus to receive data from a phone, packets are in chuncks of 256 bytes, which is the "most used"...
When I flash the card and run it, I encounter the screenshot I shared in the attachment. The error "Modem has crashed, reason 0xfff, PC:0x0" occurs. Can't I send messages...
Hi.
We are using nRF52833 (on BL653 module) where UART0 and UART1 are used for communication purposes (one with STM MUC and the other with quectel modem). Current solution...
I'm working on a personal project and have designed and printed a small prototype board containing an nrf52810, external antenna, couple of crystals, and a ws2812b onboard...
Hi,
We are developing a mesh network. Our requirement is the one device can connect to three other devices. Using one connection as a peripheral and up to two connections...
I am working on iOS pairing and bonding and connection and disconnection through UART.I am facing issue where pairing is initiated after that the device is getting automatically...
Hi,
We are experimenting with Distance Measurement feature a we observed 2 issues.
HW: Custom HW with: CR2032 coin cell -> joulescope -> 40 uF capacity in ceramic caps...
Hi all ,
I 'm experiencing issues with MQTT client connection on an nRF9160 board via LTE -M .
Some context : I 'm trying to connect to a MQTT broker via LTE -M (actually...
Hi , I am wondering if anyone with SPI expertise can answer this Q , I 'm using an nRF52840 with spi_transceive_dt()
In my devicetree I've configured SPIM on SPI3 to talk...
Hello,
I used the default sample from the nRF SDK with the same prj.conf file. I can flash it to the board successfully, but I'm seeing an error in the terminal. My toolchain...
nRF5_SDK_17.1.0\nRF5_SDK_17.1.0_ddde560\examples\peripheral\blinky_freertos
nRF5_SDK_17.1.0\nRF5_SDK_17.1.0_ddde560\examples\peripheral\blinky_rtc_freertos
I burned these...
I am using nRF52840 to interface my MPU6050 sensor via I2C , I build and flashed the program and there were no problem. But I can't see any clock signal on the default I2C...
I'm trying to build the zephyr/samples/net/sockets/http_client. I selected thingy91_nrf9160_ns for the board config and it builds and works fine. However when I enable
...
