I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello, I have installed nRF Connect and the Programmer following https://infocenter.nordicsemi.com/pdf/nRF9160_DK_Getting_Started_Guide.pdf At step 3.2.2 i see "No devices...
Where can I find a drawing of the footprint for the nRF52840 WLSCP? Normally it would be near the end of the datasheet, after the mechanical drawing of the package. The datasheet...
I have an application running a serial communication through a RS485 interface. I have two sensors attached through I2C/TWi.
I have a app_timer that quwry the sensors once...
I have built on the CoAP example a POST request to the server. This works now without any problems.
I do send the received signal power within my POST. To get the power...
Hi,
I purchased a NRF9160 DK and am having problems on the first time I am trying to compile the SERIAL_LTE_MODEM application . I followed the steps according to the documentation...
Hello,
when I open any example Project from https://www.nordicsemi.com/Products/Development-software/nRF5-SDK with Keil MDK v5, I directly get the Error Message "Cannot...
Hello,
I'm a beginner of nrf5340, when I tried hci_pwr_ctrl(ncs v1.5.1) , I met some problems.I adjusted the tx power and changed prj.conf :
Then I added hci_rpmsg...
After updating nRF Connect and the Programmer app, DKs aren't being recognized when clicking on Select Device.
Tried both with nRF9160 and nRF5340 DKs and neither was detected...
I'm working with the PCA10040, the SDK V11.0.0. and the winbond memory flash W25Q80BV.
For the SPI connection I'm using the the SPI2 because TWI0 and TWI1 are being used...
Hello
First of all, I`ve been spending way to many hours trying to figure this out, so I decided to open this ticket. I am new to microcontrollers in general and the Nordic...
Hello:
I'm new on nrF52832 development. I did some tests using nRF51 and so far so good. However I received a few samples of E104-BT5032 from eByte http://ebyte.com/product...
Hi,
I have 2 SES projects that both require softdevice plus application.
One of the projects combines application and softdevice into the .hex file that is generated...
HI
I am Programming in Keil IDE and I am using ST link v2 like debugger, but in Keil shows this problem "internal command error"
what is the problem? I was thinking...
I'm trying to build support for uart async api by adding:
CONFIG_SERIAL =y
CONFIG_UART_ASYNC_API =y
to my prj.conf. Without CONFIG_UART_ASYNC_API the app compiles...
