I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
when I used simulator in keil5 for NRF51 software debug, there is a problem : *** error 65: access violation at 0xFFFFFFF4 : no 'write' permission. When I used the keil5 command...
Hi,
I am using nrf52840 DK and SDK version 17.0.2. I want to write data into particular address location(application area) of the flash using fstorage. It is writing the...
Hello ,
On NRF52840 DK my logger works fine and I get no problem with printf(). However, on my custom board the program goes into hard fault with the following :
0x4001...
Hi there,
I'm using nrf52840 DK and Custom board, SDK 15.1.0, Segger Embedded Studio(SES v5.20)
my issue is when i receive data from uart interrupt based on serial uartes...
Hello Guys,
I'm developping and st7789 IPS screen driver and i'm having problem with SPI0 . I'm using NRF52840 DK 2.0.1
First I took SPI example from sdk 17.0.2 configured...
Hello All,
I am using SES on BMD340 controller with FreeRTOS project.
After few modification in the code, I am facing *.elf doesn't exist during linking stage. There...
On a nRF52833 on a custom PCB, due to space and allocation limitations, I need to run UART Rx and UART Tx over GPIO pins that are limited to standard drive, low frequency...
Dear all,
I have a NRF52832 module (EBYTE E73) and before yesterday, everything was fine.
We had a outdoor test last week and till then, everything was fine.
After...
I've tried this with both 1.5.0 and 1.5.1, with the same results. I install the SDKs using the toolchain manager, and when the installation finishes I open a bash shell, also...
I'm learning how to use OTA DFU on Win10 laptop. I followed this and this guide step by step. I have a couple of questions:
1) (See below code) How to use " arm-none-eabi...
I've recently purchased a Thingy:91 and wasn't able to update its firmware via nRF Connect. I'm guessing this is because that there is no MCUboot on the Thingy:91 that I have...
Have a USB powered Chengdu Ebyte nRF52840 Dongle (PCA100059-style) that has the following:
- USB 5V
- VBUS pin : connected directly to USB 5V
- VDD pin: not connected...
Hello Nordic!
I've been implementing some more commands in my endpoint handler but (I don't know how) it has stopped working. I have added the responses of the commands...
I'm getting started with an (older) nrf52840DK board. I'm following the instructions presented here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
