Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I am using the nRF51422 development kit with the SDK 11. I am trying to run the proximity application located in ble_peripherals. When the project is build I am receiving...
Hi,
I am using ble_sdk_app_hids_keyboard example:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_hids_keyboard.html...
Hello, I lived in Taiwan and I followed nRF9160 DK Getting Started and met a problem at establishing connection with nRF Cloud with my board.
The previous steps are all...
Hello, I'm trying to run C++ code on the nrf52832 but I'm getting an Hard Fault when sending a floating point to an ostream, like in "std::cout << 13.5f;". The FPU is enabled...
Hi All,
I'm trying to interface a SD Card with nRF52840 DK.
I've got a SD Card socket and a FAT32 formatted 8GB sd card.
When I run, fatfs example , I get following...
hello,
i am using nrf52840 in our customised board with sdk 15.2 and trying to achieve long range with coded phy using long range demo example as base now i could be able...
Hi,
I have two boards NRF52840 DK and I wanted to use example for BLE Central&Peripheral NRF Relay. I have just run example with Heart Rate peripheral and I can see that...
Hi there,
When I program my nrf24le1 in Keil uVision, I notice that when I load the program to the flash memory of the connected motherboard6700 with the nrf24 radio module...
I have downloaded the Kiel and uVision file (the nrf Probe) found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series and have gone through...
Hi,
I am using Keil 5 (downloaded with this link: https://www.keil.com/demo/eval/c51.htm ) and have downloaded the nrfProbe to this file. This is being used to program...
Hi, I am try to implement UART SERIAL Bootloader for my device and I just need to perform DFU using uart serial
I have tested the code and bootloader. My query is
Without...
When I run the "ble_app_blinky_pca10040_s132" example from SDK 17.0.2 and 15.2.0, right after Connected I'm seeing that device is Disconnected from device.
I tried with...
We need to programatically (on the Raspberry Pi using Python) send and receive characters to and from a smartphone using a custom service over BTLE. I have used the blinky...
I am trying to communicate with my IOT using wired uart serial port. I am using 840(MCU) (with softdevice #113).
code:
My Issue: Each time I am trying to run it while...
