Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Dear Nordic team,
I am using a NRF52832 and SDK15.3 + SD6.1.1 and Segger Embedded Studio to develop my code.
I started developing my code from the example "ble_app_template_pca10040_s132...
Hello,
I'm trying to use an oscilloscope to profile my current consumption on the nRF9160DK. I'm setting up according to the spec here: https://infocenter.nordicsemi.com...
I am now using SDK1.3.0-rc1 with NRF9160. I use the serial_lte_modem project and using nrf52 to send at command for controlling nrf9160.
I can connect to the network,...
Hi every body, I am using nrF9160 SDK. I am testing the sample project Blink_LED. In the documentation is written that LED1 is connected to P0.02. If so then why the voltage...
Hi, I would like to measure the elapsed time difference between using FPU and not using FPU in my app (nRF52840). I'm thinking to use the FPU FFT as the base example. So I...
Hi all,
I'm working on a custom Bootloader for my nrf52840-based board. The bootloader needs to support DFU from external SPI Flash. So far, my bootloader can read from...
I am working on the Thingy_SES_FW project ses file provided here . I have the goal of compiling this file. However when compiling errors(shown below) core_cm4.h: No such file...
Is there a notification signal that the ZBOSS provides that will let the coordinator (ZC) know if a router (ZR) that was in the network no longer present?
For an example...
Hi, I have been trying to get Thingy91 to work with the LwM2M sample found here . It works fine with the nrf9160 devkit and it seems to work for ~1min or so with the thingy91...
Hi,
I am using NRF52832 with NRF SDK 15 and Mesh SDK 4.0.
As my knowledge, I can update firmware for my device using SDK15. I want this cause my network does not have...
Hello,
As specified in the subject, I would like to know if there's a way to verify that a peer is already bonded with my device. My goal is to verify if a device is bonded...
hai ,
in my application i m using ble_app_multilink_central example for connecting with multiple peripherals.
how to connect with multiple connections ??
tried with...
Hi,
I would like to use the nRF52840 DK as a BLE Sniffer.
I followed nRF Sniffer for Bluetooth LE v3.0.0 User Guide but cannot run the DK as what is expected.
I...
Hi,
there are some erratas from the BT SIG mentioned in
https://www.bluetooth.com/specifications/errata/
Are they fixed/handled in softdevice S132 6.1.1 or any other...
Dear All, I am trying to add a custom service on the ble_template_app that I have managed to run successfully on the nRF52820.
I have successfully created the custom service...
