Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi, I am using mesh sdk 3.20 and nrf52840.
I am using 3 nodes for testing. One generic on off client and two generic on off servers.
I believe that I have managed to get...
Hello, I am working on a project where I have 2 nRF52832 boards with the PCA10040. I have the example developer code examples. I am using the central and peripheral code examples...
Was looking through the reference designs you have in github .
I figured the difference between nRF52840_qiaa_var1 (what is qiaa ?) and nRF52840_qiaa_var2 is the use of...
Hello everyone,
I am facing an issue with UART communication from my nRF52832 to my GPS module.
I precise that communication in the other way works very well (I get...
We have a need to invert the TTL logic for the serial interface. All our "Unique" SWI serial interfaces use an inverted logic e.g. idle state 0 instead of idle state 1.
...
Is there any lnk which uses nrf52 mesh without models.
Means a simple function to send data(like "Hello world") to any node or group in Mesh.
and other node receive data...
Hello, I was wondering, Firstly and more important question, Is there a way in a BLE Mesh standard to physically locate/position the nodes? In order to obtain the distance...
Hello,
After (accidentally) entering bootloader mode on my nRF51 DK (PCA10028), the device doesnt show up either in the device manager or using nRFgo Studio (both not normally...
I bought Nordic nRF52840-DK at an electronics store in Taiwan. J-link cannot be detected when connecting to a computer. I bought two pieces nRF52840-DK. One of them can be...
I've been having lots of issues putting the example projects on the NRF9160 dev kit. It builds without errors, connects to J-Link, but sometimes fails on the download step...
I'm unable to program a nrf52840 dev kit (BMD340 dev kit) using the attached hex file combination of Bootloader and softdevice. Both bootloader and softdevice can be programmed...
Why do I get the folowing error with mbedtls when doing "west update"?
Possibly related issues: * devzone.nordicsemi.com/.../west-update-blocks-and-fails-on-mbedtls (Didn...
Hello All,
I loaded the last FW version (mfwnrf9160100) in my nRF9160 SDK using nRF Connect Programmer and looks fine.
However, the Reset button or AT commands are not...
How would I take a NRF51 Dongle that has the stock firmware from nRF Connect and communicate/send commands to it over something like PuTTY? I've tried sending AT Commands...
Hi
configure as:
ROM start: 0x26000
RAM start: 0x20002218
when I download application software , it pops up following error.
I'm using keil uVison version 5...
