I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I am currently using SysTick to count milliseconds in my device. This works fine, however with it enabled I can't sleep the device as it wakes up instantly.
I have tried...
Hi,
I'm not sure if I'm doing something wrong so I'm hoping someone can help me. After updating from 0.11.4 to 0.12.0 of pc-ble-python-py, I get the following error. I've...
Hi,
Please help to suggest if 10K Nodes in a single network with 100 Kbps data rate is achievable with data transmission interval being roughly every 30 seconds.
This...
I have the debug section of the evaluation board turned off, modifications to measure current with a DMM set up, and am using a keysight 34465a DMM to measure current. The...
Here is the code snippet initializing the Heart Rate Measurement Characteristic in the BleHeartRateMonitor example:
static uint32_t characteristic_init() { uint32_t error_code;...
When using nRF Connect and 52840 Dongle, the normal BLE scan app works fine but connecting to the RSSI ap, the reprogramming of the dongle fails with timeout.
Hi,
I have nrf9160 DK.
I found there is u-blox driver available. Is it possible that the 9160 modem can be added an interface as a modem using u-blox? If so, there is...
NRF_LOG_RAW_HEXDUMP_INFO() is not printing complete Extended Advertisement data in HEX format. It just prints first 80 bytes of whole advertisement packet.
I added below...
Hi Nordic Developers,
Service Discovery Protocol (SDP) is a protocol for Bluetooth to detect the service nearby and to determine their characteristics by using UUID.
I...
Hello!
I am trying to lower the sleep current of our custom board. Right now in sleep, the whole system have a current consumption of 100uA. There might be component choices...
I get answer from msromero that If zigbee network is open, then new zed can join this network.
What means that nework is open ?
I want zigbee netork is silently joinable...
HI, i would like to get device name and print to uart, but when i try to print the device name i got error character.
Here my snipet code and uart result
Hi.
My target device is nRF51822 and SDK version is 12.3.0.
I try to add Device Information Service to example "ble_app_uart_pca10028_s130"
---------- main.c (added...
Hi,
I am using NRF52832 sdk 15.2.0.
I am trying to do a device firmware update by following this link: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting...
