I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
HI,
Just like discription in the ttitle. I cannot find functions (sd_ble_gap_address_set() and sd_ble_gap_address_get()) in ble_gap.h.
How can I set device address?
...
I apologize if this has been asked in a different way but I have come across several older threads that seem outdated and was hoping for the new "best practices" for the current...
Hi,I have a problem.Sometimes the program will execute to 0x08c8 during simulation on NRF52832，SDK15.2.0，Mesh3.2.I checked the map file, which is part of Softdevice.So I think...
Hello
Using PCA10040 dev board,
Building with SDK 16, & S112 - using ses
Running ..\examples\dfu\secure_bootloader\pca10040_uart_debug
Using nrfutil to download...
When running the "nrfjprog --recover --log" command, on a Windows 10 pc in CMD, this is the output that I get. I am unsure what steps I need to take from here.
Any help...
Hi,
In my application I have a requirement to send notifications to mobile on triggering particular Interrupts as well as particular events.I have created a customised notification...
Supported tx_power values: -40dBm, -20dBm, -16dBm, -12dBm, -8dBm, -4dBm, 0dBm, +3dBm and +4dBm.
What is difference in the behavior of nrf 52832 chip for these different...
We're developing Bluetooth tags that we would like to operate at both 1Mbps and coded (long range). From what I've read and seen from the Nordic testing, specifically "Testing...
I modified the gpio interrupt on the asset_tracker example of ncs v1.2, modified the following, and the interrupt didn't work: Where is available should be modified.
I set...
Dear Friend，
Based on nRF52832, mesh3.1, port ble dfu to mesh project, Android dfu application is based 'no.nordicsemi.android:dfu:1.10.1'; Call the following program: ...
My setup: custom board using nRF52840, Segger Embedded Studio 3.52, nRF5_SDK_for_Thread_and_Zigbee_v4
I used a couple of your projects as a starting point for my code. Specifically...
Hi,
In my proejct, I am using WFE(); in some while loops because of core low power mode.
For example, waiting for time_out flags like codes below.
I am wondering if...
Hi All,
I'm new to the nordic product. We previous using TIcc2642 as development board. And we would like to test our application over different hardware. Is there any...
Im using CUstom BLE tutorial example and it works fine. But i just wanted to know, in which section is the text data for logging occuring. Ex: "notfication received from ...
