Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I am on the learning curve of nRF9151 and LTE/GNSS.
Trying to build and run the sample app under nrf/samples/nrf9160/location
The errors Im getting are
[00:11:23.476...
Hi, I have upgraded my custom nRF52840 devices from SDK 2.4.1 to SDK 3.0.2. For few days, these devices did connect to existing OpenThread network. But now, all SDK3.0.2 devices...
I used the Bluetooth mesh distributor example from ncs2.9.1, and the Bluetooth mesh dfu can proceed normally. However, when I tried to pause and resume the dfu process, I...
Dear Nordic Support Team,
nPM2100, SHPHLD pin: we would like to connect a pushbutton to GND to wake the PMIC from ship mode. Additionally, we would like to read the pushbutton...
Hello, I am currently designing a custom board using the nRF9151 and I have a question regarding the SWD interface. My understanding is that the nRF9151 contains two main...
I've just spent about 4 hours trying to figure out why a particular build was failing (on nrf9151dk).
Examing the cryptic errors finally revealed that the TFM partition...
We're using the nPM1300 in our designs and we noticed that the charge portion does not appear to keep a battery charged when USB is connected for extended periods.
Our arrangement...
So far we have been using nRF5 SDK v17.1, but we ended up using nRF connect SDK v1.9.1.
However, this compiles too slowly.
I modified main.c and it seems to compile everything...
Hi,
I’m using NCS v3.1.0 and noticed that my application does not run unless I enable:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC=y
Without this configuration, the system fails...
HI TEAM,
I am using a custom board and measuring its overall current consumption using the NRF Power Profiler Kit 2 (PPK2) .
Setup details:
Power source: External...
Hi,
We are using the nrf9151 to get GNSS data/coordinates without using A-GNSS, we followed the information in the following page "https://docs.nordicsemi.com/bundle/ncs...
Hello Nordic Support Team,
We are currently developing an IoT product using the nRF9151. In our application, the device wakes up once per day, transmits a small amount of...
Hi, everyone
I am currently working on the development of Bluetooth and ANT+ on the nRF52832 chip. It communicates with my chip via UART, and now there are occasional disconnections...
