Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I have a BLE sensor node (firmware not modifiable) that takes up a peripheral role and starts advertising when powered up. Typically, one can scan for the node from...
Hi All!
I have been working on bringing-up a custom manufactured nRF52832 board. I have with me 6 boards, the first 3 are working fine, the other 3 are not. In both cases...
Hello all,
I'm practicing creating my own service following instruction from this link: https://github.com/bjornspockeli/custom_ble_service_example
Now I stuck at part...
Hi everyone,
I have configured two UARTES , one using the app_uart library and another using nrf_serial library.
I am using SDK15.0 alongwith s140 softdevice with bluetooth...
Hi There,
What are the difference between system off, ram retention, RTC wakeup vs system on with ram retention, RTC wakeup vs FreeRTOS tickless with RTC wakeup? And what...
Hi team,
I noticed a very interesting incorrect pin description in the latest product specification of v1.2 for nRF52810, QFN32.
Above picture shows we have 2 p0...
I'm using the PCA10056 with an SD card connected via P1.12-P1.15. When I use the FatFs example of SDK12 PCA10028 it works fine. but when I use the FatFs example of SDK15.0...
Hello,
I've got the nrF52840 and would like to create a simple application to send temperature to my laptop. Then the next step would be to create some mesh network with...
Hello,
I am working on Custom BLE HID Keyboard. I am currently trying to understand working of program given by nordic in SDK-10.0.0. THere is one problem which I am facing...
Hi,
I've tried to implement the DFU_buttonless example to my development board. I programmed the bootloader and the settings-page. The bootloader detects the application...
I'm currently in the prototyping phase of getting two nDK52840 boards talking to each other. I currently have one board flashed with the central role, and another board flashed...
Hello.
What do I need to run this example called uart?
As far as I understand this should be simple echo program meaning what comes in goes out but I can not see anything...
I want to use nRF52-DK for receiving data over UART and send it over BLE link so I loaded the ble_app_uart but hard fault occurs immediately in these circumstances - 1. If...
UART works fine as long it is configured on port 0:
But if it is configured to port 1, it does not work:
and compiler reports a warning in serial_uart.c, serial_uart_init...
