I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Can the nRF52840 dongle be used to sniff/record BLE communications even if the recorded packets cannot be decrypted, or can it only record packets when decryption is possible...
Hi all,
I got thread cli working and now I tried to set up a thread network.
I built the sample for the nrf5340PDK with overlay-minimal-multiprotocol.conf and overlay...
I currently trying to get my DK connected to nRF Cloud, I am based out of Western US and I have already provisioned my SIM card. I followed the documentation instructions...
In my program, there are different sections like each section does a different task and I am trying to use a different clock frequency for each section. So, I want to know...
Hello, I want to develop applications for my Mac and for iOS + Android smartphone. First I created a simple Mac gatt server with apples CoreBluetooth API which has one service...
Uart is initialized in non blocking mode but i need to use blocking transfer in a spacial case: is there any function available for this.
I can not reinitialize nrf_dvr_init...
Hi,
I have an issue when I want to read an attribute from a toll to my nrf52840 device.
For exemple attribut 0 of cluster basic, if I forge a general read request for...
Hi,
I am in the process of porting an application from an nrf52 to an nrf51 due to availability issues. One problem I run into is that bluetooth events are handled in...
The board connected to the PC for the first time, but after I mistakenly loaded the Bluetooth low energy sample instead, the Power profile on software nrf connected for desktop...
nrf51822's SWDIO/nReset pin is controled by a MCU GPIO output, a 1k resistor is in series. SWDCLK is connected to a pull-down resistor. And sometime (very rare) nrf51822 can...
Hi,
I am using nRF9160 multi cell location code on nRF9160-DK PCA10090 version 0.15.0.
Modem FW has been updated to the latest 1.3.1 binary.
I am using LTE-M with AT&T...
Hello there,
Recently I have added and been testing DFU into my existing application. I have conducted a few DFU updates and have noticed a semi-reoccurring issue. I use...
I currently have a working project with ethernet shield ( ENC28J60 ).
I use the driver from NCS 1.5.1.
I want to know how to enable logging?
I found some posts on this...
I am current evaluating the SPIS for the nRF52840 and experiencing incomplete transfers from a connected master (Arduino). I'm sending 'hello world' from the master to the...
