I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
dev environment segger embedded studio with nrf5 sdk
I have separated my project source and the paths of nfr5 sdk the project have different folders for different drivers...
I'm using led1 alisa for indication that network core is runing. But if I compile program, variable is not initiated from DTS. It looks like compiler does not init dtLed variable...
Dear Nordic,
we are developing FW based on nRF52832, SDK 17.0.2. We have 2 devices: BLE Central with SD S332 and BLE Peripheral with SD S112. The Peripheral is basically...
Hi, I am working on an IoT project that will use lwm2m, I developed an event manager architecture using the helloworld example base. Now that I am starting to develop the...
Hi,
Is it possible to check somehow if a BLE packet has been transferred (or not) from a peripheral to the central device?
Through a succesful transmission flag or something...
Hi, I'm using nrf52832 custom board and 14.2 SDK, S132.
In my program I'm using SAADC, PWM, I2C along with softdevice and PID. my device is working fine for some time but...
Hi! I've noticed that softdevice S113 is Bluetooth 5.1 compliant , and that the nrf52 family chips are Bluetooth 5.2 compatible in terms of hardware. a. Is there any target...
fds_init fails for several valid reasons, but my issue is how to recover. This for me was triggered by a firmware upgrade overwriting the fds file area. This can trigger fds_init...
Hi, I learned how to replace the softdevice for a normal application. I've replaced 140 with 340 in my app. However I don't know to do that for the boolloader.
What I want...
Hi Nordic,
I want to control an LED with the nrf GPIO, the LED Anode is connected to VDD, through a resistor, and the cathode is connected to the GPIO. Under this configuration...
I want to use the nPM1100 to battery manage, and supply power to the nRF52xxx - along with a heavy duty load ***directly across the battery***, so that full battery voltage...
Hi,
I'm running the experimental example: 'ble_nfc_pairing_reference_pca10400_s132' using sdk17.0.2 (and 17.1.0).
After I installed the micro-ecc following the guide on...
Hello
I am evaluating design of wireless communication in power supply with nRF24L01P , and I have 4 questions.
1.I want to know the Mean Time Between Fails (MTBF) and...
I'm using softdevice s140.
My power comes from a CR2032 coin cell.
My board has a 1.8V LDO (Toshiba TCR3UM) because my temperature sensor is calibrated for 1.8V (TMP112B...
