Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi
I would need to work on Master Branch. I have Toolchain Manager 0.10.1 and I have downloaded nRF Connect SDK 1.7.1.
I know that Toolchain Manger has not Master branch...
In my project an interacting with the ncs 1.6.1 peripheral _uart example and my plan is to ensure that data size being send at a particular time is increased to send at least...
Hello everyone,
I went through the forum and saw some topics regarding the implementation of the characteristic read out over sd_ble_gattc_read. I implemented it as desribed...
Hi all,
I would like to know, if any example code available for AoA algorithm for ble direction finding. I am working on a project for indoor positioning and tracking...
Hi,
I am trying to sample a large quantity of sensor data from the nrf52840dongle as the server and the nrf5283dk as the client. I have used the peripheral uart and central...
Hi all,
So I want to give you a full description about what we are doing because we could not understand what we did wrong.
Our DK : dk-51
Soft Device : S130_v1
Our...
Description:
I try to initialize a SPI device in my nRF52DK through the Zephyr‘s driver(drivers/spi.h).
Code seems correct when compile and I got no error when build the...
Hi, I am new to Zephyr and Nrf, I am trying to replicate the event manager arch from asset tracker v2 but I am stuck in the setup. I am trying to use the logging capacities...
I am working on the Electronic Braille Display for visually challenged persons.
Our device will communicate with Voice over service on the laptops and smart phones using...
Hi,
with %SHORTSWVER: nrf9160_1.3.1 I am getting:
AT%CMNG=0,3,4,"test1234" OK
AT%CMNG=0,3,3,"30313233343536373839303030303030" OK
AT%CMNG=1 %CMNG: 0,6,"0606060606060606060606060606060606060606060606060606060606060606...
I have a single sample of the new nRF52840_XXAA at hand on our custom board. I'm trying to do a --recover with nrfjprog. As the log below shows, nrfjprog recognizes it as...
Hello ,
I m using SES v5.6 and NRF52805 ,ble_app_uart ex (nRF5_SDK_17.1.0),
Requirement -need to wake up and reset ( or start advertising again) from sleep mode ,when...
Hello,
I have adapted some of the ESB proprietary Protocol from the NRF SDK into my own project without installing the SDK directly; however, complete integration seems...
Hi Team ,
In my application , i am using RTC1 for RTOS and RTC2 for Running a time calibration andRTC0 for Softdevice but parallelly i need to add Lbs service which includes...
