Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi nordic,
After I transplanted nrf52832 to nrf52833, the upgrade of nrf52833 failed, or stuck in the bootloader.I tried to use the current method to upgrade nrf52832, it...
Hi
Problem description：
In application serial_lte_modem ,When sending AT command "AT + CFUN?"， return"at_host:Error while processing AT command:",What caused this？Thank...
Hello,
We have a nRF52840 on our board, whose fw we would like to be able to update through both BLE and UART (the MCU is connected to a ST32 MCU via UART) using a bootloader...
Hello Everyone,
I am currently using the AGPS example on the nRF9160-DK with nRF Connect SDK v1.7.0. I notice it requires 4 satellites in order to provide a position fix...
Hi,
I need to use system tick to do some math calculate. So I create a new function to get systick like as below. then I can get some number.
And I create a 200ms timer...
Hi,
I'm new with BLE development and I'm trying to find a module that can be used with an Atmega328p and libraries that allow me to create a GATT profile (creating services...
Hello, everyone.
I'm beginner at this, and I need your help.
As the title says, which of the GPIO pins can be specified for PWM?
I am waiting for your answer.
Dear Members,
I want to run :
E:\nRF5_SDK_17.0.2_d674dde\examples\peripheral\spi\main.c
on this line :
APP_ERROR_CHECK(NRF_LOG_INIT(NULL));
I get :
error ...
Hello, I have an application using nRF5 SDK 17.0.2 and SoftDevice S140, I would like to implement the mesh function on my devices and I have some doubts.
1- What is the...
I tested it in a conductive way. The transmission power of +8dbm is set on the software. Remove C3 and L1 and connect the RF line directly to the ANT PIN to test the transmitted...
Trying to understand how interrupts work on nRF52: does setting an INTENSET register of the said peripheral enable the interrupt, and to propagate the interrupt over the Cortex...
My operating system is window 7, and I have been using nrfjprog v10.12.2 before. When I updated nrfjprog to v10.15.0, the following error occurred when using nrfjprog -v....
Hi there,
I want to run FATFS example but I got this error ?
========================
nfo> app: FATFS example started. nfo> app: Initializing disk 0 (SDC)... rror> app...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I found that the maximum clock frequency of nRF52832 is 64MHz, but I don't know what the current clock...
Hello,
I know there are dozens of threads on this topic already but they don't seem to quite answer all my questions.
Some background:
SDK: 15.2
SoftDevice: s140_nrf52_6...
