hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hello, support team:)
Currently I am working on SPI communication with LSM6DSOXTR.
CLK, MOSI, SS is working as expected. But there is no MISO signal.
0) All SPI...
Hi,
Just would like to know is it possible to proceed auto pairing by restore the MAC address of host?
The current idea is using direct advertising to speed up the pairing...
Can a provisioner work as a client connect to a server
how do I set on the phone app(iPhone 10s)
in example/light_switch I did not do any change on the example
...
Hi,
I'm in the process of integrating nrf52840 module in HCI over UART to a linux host.
So far I have been able to build the hci_uart in from the samples and bring it...
Dear Members,
How can I share GPIO pin between SPI and I2C peripheral ?
I see SCK_PIN and MISO_PIN for SPI are the same with SCK and SDK on I2C
#define SER_APP_SPIM0_SCK_PIN...
For reference I am using the nRF5 SDK version 17.0.2. I have been comparing the flash_placement.xml files in the <SDK>/config directory and in some of the examples. I have...
Hi. I am looking for simple example of using QDEC for nrf5340. I want to use the Segger Embedded Studio.
Where can I find the example of some guide for HW driver for nrf5340pdk...
i am using nrf52833 development kit here i am using peripheral template as for coding purpose when i merge temperature sensor(SSTS751) code and W25Qxx code in it then the...
I am trying to build the connectivity hex files on an ubuntu build machine for an nrf52840 dongle so I can communicate with another nrf52840 dev board, I followed the instructions...
Hello, my project has 3 different devices (2 sensor and flash memory) on the same SPI bus all with their own CS. I ran across the following question , which has a response...
Hi ,
My environment :
nrf connect sdk
nrf5340 dk
segger studio IDE
verified method 1:
As per nrf5340 product specification document , we can protect the...
Hello,
I was recently trying out some samples with the nRF9160 DK and I had run into some issues when trying to run the nRF Cloud Client Application .
I had flashed...
Hi,
I'm developing on the nRF52 DK which has the nRF52832 chip.
I have a small vibration motor which I'd like to control on/off through one of the boards GPIO pins. At...
