hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
It's my mistakes.
1.I want to measure temperature from DS18B20,but I don't confirm the capable of the pin - P0.05.Because it's Analog ，but DS18B20 is Digital.
2.I set the...
Hello, I'm getting started with a nRF52832, I've got the SDK 16.0 installed and what I think are all the latest packs installed. I try to build the examples\ble_peripheral...
Hello everyone.
I'm trying out the "Zigbee Multi Sensor Example". infocenter.nordicsemi.com/.../zigbee_multi_sensor_example.html
I have 2 nRF52840 devices.
I wrote the...
When my program starts, I set up a watchdog timer for 100 milliseconds and I start a repeated app timer that runs every 90 milliseconds to feed the watchdog. I use the app...
I'm trying to send data via UART from a NUCLEO-F401RE to the nRF 52840 DK. But the data I send is not comming through correctly. For example when I send 3 the nRF prints 32...
I have an existing product to which I need to add SPI to get Wifi compatibility. Basically the Nrf52 is acting as central and passes BLE events on to an ESP32 with Arduino...
Hi.
I have nrf52840-dk board. i tried the UART example from the peripherals directory. it works with the default, if i open a console on /dev/ttyACM0 and on /dev/ttyUSB0...
Wanted to ask if there is any example on configuring the GPS into single shot mode.
I know the asset tracker can operate in continuous_mode and continuous_power_saving_mode...
I am attempting to use SDK15 with the nrf52832 to communicate with multiple sensors over I2C. However, in the twi_sensor and twi_master_using_nrf_twi_mngr examples, as well...
I am using the nRF52840 with the SoftDevice disabled to run a proprietary RF protocol. For much of the time, I have the radio in continuous receive mode by making use of the...
I have a nrf52 application that samples four saadc channels at 1kHZ. That is: Map four pins to ADC input and let Easy DMA take care of the sampling so that the data is processed...
Hi,
I have measured QSPI current consumption on our product at no access period, and got 1mA (too high current!).
So I tried to check with nRF52840 DK to confirm our...
I need to have two different peripheral profiles (with different addresses and so) that will be advertising at same time and that can be connected by different centrals at...
Hello,
It might be a stupid question but I wonder if it is possible to use the ZCL generic command from the CLI to send ZDO commands? I tried it with the ieee_addr ZDO command...
We intend to use the ZigBee stack together with another communication stack and BLE. For the other stack we also have just a library (.a file).
Now we get an error message...
