We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hey , i'm using nrf52832 with SDK 14.2 . I'm trying to send 3-axis accelerometer data through BLE . Is there any example for SDK 14.2 to achieve this ?
Hi,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
As shown in below snapshot I am just doing below...
According to the blog below, hardware design of nRF9160-SICA has been fixed on May 31st. https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/nrf9160-development...
I am designing a pcb just the nRF 52840 MCU. The design of the PCB is based on the reference design from Nordic. When ordering the PCB I came across a problem that the vias...
I have 4 gpio inputs on the nRF52840 working and sending these states over the BLE. I tried to add a few more gpio inputs but I get an error =4 which I think is NRF_ERROR_NO_MEM...
Hello,
I can successfully put my nRF52832 into System OFF mode, however, the Debug Mode Interface is still running, so the current consumption is > 2mA. What are the command...
I have a nRF9160 DK need to update modem firmware to v1.0.0
According to C:\nRF91\mfwnrf9160100\README.txt below, I should use nRF Connect Programmer to update modem firmware...
In the light_switch example of nRF5_SDK_for_Mesh_3.1.0, I noticed that generic_onoff_client.h has a union for holding the current message packet. However, there is only one...
The timer example with SDK 15.0.0 uses the old timer driver. Is there any example code showing how to use the current nrfx_timer?
I'm just trying to generate a periodic...
Hi Nordic team and fellow fans,
I am trying to switch from SPI to SPIM and getting an odd assertion with no context after I kick off a SPI operation, but it only happens...
SDK15.3.0
nRF52810
the original secure_bootloader and buttonless_dfu works fine.
nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040e_ble
and nRF5_SDK_15...
Hi,
I am using the nrf52832 dk,
i want to decrypt the data i receive over ble (AES encrypted data will be sent over ble) which api's or sample codes should I use?
Hi,
In the cops=0 state, how long does the modem take to scan each band of both cat-m1 and NB-IoT? How does a roaming sim affect these times for both technologies? In...
Hi
I would like to give a try to nrf52 on mbed. So I went to:
https://os.mbed.com/teams/mbed-os-examples/code/mbed-os-example-blinky/
and clicked Import to compiler...
The demo board would not connect (no second LED)
Since in Italy we only have NB-IoT, I guess I should recompile a more recent version of the demo application.
I have followed...
