I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello,
I'm working in NB-IoT and I've been trying to flash the UDP_with_PSM sample ( https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/udp_with_psm...
Hi All,
I live in India
City: Pune
I got my Thingy91 yesterday, but later I realized that as there is no support of NB-IOT or LTE-M in India, I am not able to activate...
Hello,
I tried to mix AWS_FOTA sample with GPS from asset_tracker (see code first screenshoot) and I get that error (see second screenshoot). Do someone have an idea please...
Hi,
I am using nRF52840 DK with USB and BLE prototype under hardware peripherals example in the SDK. I need a real world example using BLE with USB as host interface. Can...
nRF52840 works with 1.8V supply voltage? We are using Circuit configuration number.5. it tells VDD should connect to VDDH.
As per the circuit configuration 5: VDDH is N...
Hi :
we met some quesiton when using nRF52840:
1. Is it possible to drive a pin to high or low in sleep mode? For eg. we would like to put pin P0.12(may be other pins...
I am trying to communicate between an ADXL362 accelerometer and a nRF9160 DK. I see on this link https://docs.zephyrproject.org/latest/samples/sensor/adxl362/README.html that...
Hello
we had purchased nRF6700 and nRF24LE1-F16Q24-DK from Mouser India on 14-oct-19 .and it comes with an older version of firmware i.e.(3743) And currently, I am facing...
Hello:
I have to nRF52DK boards and I am able to run the ligth_switch example, but the thing that I want to do is send a message, "hello" from one node to other. I saw...
Sir in the above code i have a cmd_zb_match_desc() but i am calling inside the switch case but after calling i didn't able going inside the finction
please give the Suggestion...
HI,
I want to send heart rate data to smartphone using NRF51422 in every second without any time delay or minimal time delay ranges between(0.9 to 1.1 sec).
Thanks...
Hello,
I managed to get a central application to run on the nRF52810 with SDK 14.2 and S132 V5.1.0. I also got the bootloader working with this setup.
Right now I'm having...
Hi!
I have nrf52 periperial mode, SDK15, s132.
I connect a smartphon in the central mode to my nRF52 and start to send some data.
In the nRF52 I receive those data in...
Hi, I am trying to print double/float values, but Its printing blank. e.g. printk(" value:%.3f\n", value); output: value:%.3f printk(" value:%lf\n", value); output: value...
