I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello,
I am using nRF52832 EVM board with SDK 15.3.0 in SEGGER studio IDE, win 10.
When I am implementing sd_nvic_SystemReset(); in my code, that time i am not able to...
I have a custom board based on QIAA Reference Layout 1.1 Variant 6.
The application is built with Zephyr without bootloader and is placed directly on address 0x0.
When...
Hi, I'm designing nRF52832 custom board, on 'single side' pcb.
To make VDD and GND lines connect, I used 4 jumpers, which have 0 ohms.
I designed with nRF52832-QFAB reference...
I used the ble_app_uart for pca10040e successfully on the DK52, now I'm trying to port that project onto actual nRF52810 chip.
This is my build configuration on SES (Segger...
Hello Nordic Support Team,
The question I have is simple.
Can I use the pc-ble-driver with the ble_connectivity_s140_usb_hci example found in SDK15.3.0?
If not why?...
Is there any public documentation on the LTE Modem hardware API for the nRF9160?
I'm interested in porting an embedded operating system written in Rust to the nRF9160 and...
Hi,
I am using ncs 1.0.0 in nRF9160.
I have enabled UART 2 interrupt during initialization of the uart as below and it works fine.
To reduce the power consumption...
Hi,
Using the Thingy app on my iPhone works fine.
However, I would like using my iPhone as a gateway (thingy:52 -> iPhone (BLE -> Internet) -> nrFCloud. I installed the...
Hi,
I'm migrating a project from SDK 14.2 to 15.3 and I wanted to use the generic and "full" sdk_config.h located in config/nrf52840/config/.
The documentation says...
Hi everyone, I would like to confirm if this is a bug.
Per the comment, it seems that the intent of the code is to reject an attempted SoftDevice update.
However, this...
Hi,
We're currently developing nRF52832 module which can support for several products, like bulbs, switches and etc. Once we finish the developments we're try to make them...
Hi,
The final design we are working on is composed of 8 peripherals notifying (every 80ms or 160ms) to 1 central.
Packet data size is 141 bytes and depending on rate configured...
Hello,
I currently have a working BLE application for the nrf52810 which is currently using the s112 softdevice. However I wanted to increase my BLE throughput so the s113...
Good morning
Our company is using nrf52840 devices with BLE-mesh and asked me if I could have a look at the Zigbee functionality for adding Alexa compatability.
So...
