Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi
I've a problem with one or maybe two of my nRF52 DK's. If I open nRFConnect 2.4.0 Programmer (or the BLE app) and connect only one of my nRF52 DK's the device selector...
I have an nRF52 DK and a CR95HF development board from Mikroe ( https://www.mikroe.com/rfid-click) and I'm using the Nordic SPI SDK version 14.2.0
I have managed to get...
Hi all,
I'm working on a project which will automatically send data from LM75 sensor through mesh proxy_client to proxy_server. So, I did merge two examples twi_sensor and...
Hello Nordic team
I am working on ble_app_buttonless_dfu example code and implemented accelerometer code via TWI0. And Accelerometer INT pin connected on GPIO via gpiote...
I am looking to develop a number of Zigbee compatible devices for home automation. Can you tell me if the nRF52840DK and dongle (no debugging using the dongle I understand...
Hi all,
After I combile light switch example and remote example for my client and server board . Function Remote run fine . But when I push button for send unicast message...
Hi. I try to run example Light Switch Demo.
I use: Mesh SDK v.2.2.0. NRF SDK v 15.0.0. Softdevice: s132_nrf52_6.0.0.
I see that relayed messages have maximum TTL = 4,...
Hi, I already have device that plays audio from sd card. New feature is needed that user can send MP3 file to device from mobile phone that will be stored in sd card and then...
below is a little part of code copied from nrf5_SDK_for_Mesh_v2.2.0_src:
***********************************************************************************************...
Hi team,
I am integrating bmp180 and mpu6050 into a beacon code.While integrating,I am getting the following error
"NRF_ERROR_MODULE_ALREADY_INITIALIZED".
Please help...
SDK14.2
Segger Embedded Studio
nRF52 development board
According to this post https://devzone.nordicsemi.com/f/nordic-q-a/20556/how-does-the-saadc-scan-mode-use-the...
Hi All,
Currently i am working on Zephyr RTOS as a target of PCA10040 DK.I have been compiling and executing a simple "Hello World " example.
While doing cross compilation...
Hello,
I have use the BLE Multi-link Example as a central. For the priripheral I have use BLE Blinky Application and UART/Serial Port Emulation over BLE ( <InstallFolder...
Examples in SDK15 use the Observer pattern to handle BLE events (using the macro NRF_SDH_BLE_OBSERVER). AFAIK, the registered handler runs in some IRQ context, typically higher...