Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
I am developing software supporting LEsecure using SDK 12.3 with nRF 51822.
Please tell me what to do when incorrect data is entered in "Passkey entry".
Currently...
Hi.
I've been trying to send a payload with STM32F but I can not. I've used both STM32F103 and STM32F3 to send a payload but neither of them worked. However, when I use...
Hi,
I use nRF5 SDK v15.0.0. In my application I need periodically disable and enable Bluetooth because they are wifi also, which connected to the same antenna. Its mean...
Hi,
I'm trying send me the mac address of the device by UART by the following method:
By serial I receive:
Start b9:24:82:d5:4f:81
The problem its that the device...
Good day
Firstly, an overview.
I am currently busy with a technical proposal for a client. Initial details will result in a completed approx 60 000+ sensor network. My...
Hi EveryBody!
I've begin to work with the n51 family, my board is based on a n51822QFAA H1 IC.
I use Keil5 MDK and a ST-Link V2 programmer. They work fine as I've tested...
IOS, nRF Toolbox 4.4.4, DFU Library version 4.1.1
Attempting to flash to ruuvi with nRF52832 reports
:INFO:Hash failure and
:INFO:Return false in CRC
to J-Link RTT...
Hi,
I'm trying to modify the slave latency and supervisory timeout setting, but found sometimes the gap_params_init() will get error after changing.
For example, I can...
I want to implement mesh functionality. There is no problem with nrf52dk board, but I think there is a problem with board that I made with nrf52832 chip. attach the photo...
I'm on SDK 15.2 and iOS 12 with nRF52832 on a custom board.
I've added the dfu service to my existing NUS/UART service. In the nRF connect app I can see both services and...
I have downloaded SDK software nRF5_SDK_15.2.0_9412b96. I am using segger studio as my IDE on windows.
I tried compiling the Example code for SAADC. There were no errors...
Hi, On SDK12.3 when using sd_flash_write at any memory location causes the device to halt and restart. On SDK11 I've been using flash_word_write and flash_page_erase using...
Hi I am using a nrf52832 board with a BMI160 sensor. I am trying to sample Accel and Gyro at 1600hz using a timer. The timer timeout is set at 20 ticks (32768/1600) @32768...
