I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
I'm running SDK 2.8 and 2.8 Toolchain. I created the sysbuild.conf setting:
SB_CONFIG_BOOTLOADER_MCUBOOT=y
and put it in the application folder (per this support request...
Hello, I am relatively new to the nRF 5340 Audio DK. I recently ordered a singular nRF 5340 Audio DK board and my goal was for the board to take in input audio via the PDM...
Hi all,
I've been using the nRFConnect extension without any issues, successfully connecting to my nRF5340 board via JLink, flashing firmware, and receiving printed messages...
i get the following build error whenever i build for boards other than nrf
- CMake version: 3.21.0 -- Found Python3: C:/ncs/toolchains/b620d30767/opt/bin/python.exe (found...
Hello,
I encountered a compilation issue when using the app_timer function. The error message is: "'TickType_t' undeclared (first use in this function)". I believe the problem...
Hi,
I am trying to set the VDD pin to 3.0V instead of the current 1.8V (also changing the GPIO voltages to 3V). I've seen many questions related to that but no solution...
Hi Support Team
May we know that the difference between Engineering Build Code BB0 of nRF54L15 with normal Build Code? Which is recommended for the mass production of customer...
Hi, I am using nrf9151-DK to send and receive data over UDP protocol. Firstly, I tried to use AT commands to send and receive meassages as described here , I had no isuues...
Hi,
How can I control a Thread CoAP Client, which is connected to a thread supporting modem such as eero+ (in other words, the CoAP client is connected to the internet)...
Hello
I am trying to build the Zephyr mesh distributor sample on the nRF 52840 dongle
It builds and runs just find on the nRF52840 DK
But when I try to build for the...
Hello,
I'm looking at adding USB DFU to my project, (Not USB DFU recovery in the bootloader, but in runtime) and was trying this example. It fails to build for the nordic...
Hi,
im develop a keyboard by ncs sdk in nrf52840,and one funcation is that power off/on the keyboard ny fn key .i see the CAF: Power manager module , It doesn't seem to...
Hello, I've been developing on a Nrf5340 board and I am trying to gather pressure sensor data from both a adafruit mprls pressure sensor breakout board on i2c and then a Honeywell...
I've been tasked with studying adding Auracast to an application. One fundamental thing I can't get my head around is what is the s/w requirement - i.e. do I need 3rd party...
I am using download_client library in C++ project. I have to include coap.h but when I compile I get this error:
C:/ncs/v2.7.0/zephyr/include/zephyr/net/coap.h:744:16: error...
