Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,
we want to get three different states using only one GPIO:
1. nRF52840 GPIO output driven low
2. nRF52840 GPIO output driven high (3V3)
3. nRF52840 GPIO internal...
Hi Support Team
UART20 of nRF54L15 can't work when setting P2.02 as TXD and P2.00 as RXD when I test the central_uart sample of NCS V2.9.1. I find that the SPI00 has used...
Hello Nordic community,
I'm working on a project using the nRF5340DK where I need to achieve precise control over three GPIOs with the following specifications:
P0.07...
Hello,
We are using the nRF52840 on our own board.
When I added up the current consumption at 3V, based on the datasheet, I get 14.3mA (CPU from RAM, Tx at 0dBm 1Mbps...
Hello,
I'm using peripheral_past sample on nrf5340 audio DK board, and select nrf5340dk_nrf5340_cpuapp_ns for Build Target.
I added the following config to enable RTT...
Hello,
I have nRF9160, modem FW = 1.3.6 and nrf sdk version 2.7.0.
I am trying to create an outgoing socket with connects to specific port num and ip address but I am...
Hello, I am working on a project where we use MCUBoot.
Currently everything works fine, but now we wanted to introduce persistent storage of some key value pairs.
For...
Hi Nordic Team,
What is the difference between 10 bit, 12 bit and 14 bit operation mode and 8/10/12/14 bit resolution in SAADC of nRF54L?
Best regards,
Bhavya
Hello,
I'm using nRF54L15DK and nRF Connect SDK 2.9.0. I'm developing a project for PID control of the temperature of a peripheral, let's say a heater. The feedback is...
Hi,
Not able to compile hci_uart application on latest nrf-sdk Following is error :
test/zephyr=ZEPHYR_BASE -fmacro-prefix-map=/home/abhinav/nrf_latest=WEST_TOPDIR -ffunction...
When programming a nRF9151 firmware on to Thingy91 X, I made a mistake and failed to change SW2 from nRF53 to nRF91 (the label is very small). The USB serial port no longer...
Hi,
I have finished some code with nRF54L15 and nRF52833, now I want to add nRF7002 to my design and I am wondering whether this is available?
Thank you!
Hello, World
Please note that the following questions may be difficult to read as the text was created using a translation tool.
I have downloaded version 17.0.2 of the...
Hello Nordic Team,
I am working with the nRF5340 Audio DK as a central device , trying to establish a secure connection using Security Level 4 (128-bit encryption with LE...
