Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
NRF51422 Custom board
SD310 v3.0
Phone: LG K8 4G
Android 6.0
SDK 9.0.0 Boot-loader example
I am testing over the air DFU with our custom device.
a.) DFU...
Hi there,
@Simonr, I need further help on this case
https://devzone.nordicsemi.com/f/nordic-q-a/58464/filtering-based-on-128-bit-uuid
It is said that it is possible...
For power optimization I did to disable Mesh Using this piece of Code
and Re- Enable using this code
So the Real Question is that , After disabling Mesh for some time...
Hi
I need a suggestion. We are like to try a long-distance I2C communication between the sensor & Nrf5340 that is we need to connect 1.5 meters of cable between them. So...
The device advertises.
The phone scans.
The device use white listing and only allow one peer, the phone.
What's the difference between erasing bonds and disabling white...
Hi there,
I'm intending to use the nrfxlib modem library and its BSD socket implementation on the nRF9160. My goal is to use non-blocking APIs and use `nrf_poll` in response...
Hi,
I followed the DFU to SDK example post on https://www.u-blox.com/en/docs/UBX-19050198 to add Buttonless DFU to an application (I modified \ble_peripheral\ble_app_hrs...
Hi,
I'm using nRF Connect SDK v1.7.0 to develop a firmware for a custom board with a nRF52832 MCU. I'm using VSCode to build and flash my device using the nRF Extension...
Hi All,
My dev environment is as follow:
nRF52832(Central) + S132 + SES + SDK 17.0.2
Normally my Multilink Central code is flashing and working properly without...
I'd like to know of an example(s) for interfacing nRF52840DK board as a Master SPI to an Arduino badge (from Honeywell). I have the badge working with an Arduino Uno (Rev...
Hi,
If I want to use the NRF52833 as TX, and NRF24LE1 as receiver. How I can I match out the address?
If NRf24le1,
RX_addr = {0x00, 0x 11, 0x 22, 0x 33, 0x 44}
then...
Hello,
I'm working with NCS 1.7.1 and the nrf52840 dev kit to implement a BLE peripheral with FOTA, stats and configuration features. I've added MCUMGR to the project so...
Hi Sir,
As we know the inductor connected to the DCCH pin is a DCDC function for high voltage mode.
But what side effect we can see if we connected the inductor at the...
Hi,
I'm using NRF52840 to connect to an Android mobile phone.
The application scans for advertisement and when the NRF device starts advertising - connection is established...
