Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
dev environment segger embedded studio with nrf5 sdk
I have separated my project source and the paths of nfr5 sdk the project have different folders for different drivers...
I'm using led1 alisa for indication that network core is runing. But if I compile program, variable is not initiated from DTS. It looks like compiler does not init dtLed variable...
Dear Nordic,
we are developing FW based on nRF52832, SDK 17.0.2. We have 2 devices: BLE Central with SD S332 and BLE Peripheral with SD S112. The Peripheral is basically...
Hi, I am working on an IoT project that will use lwm2m, I developed an event manager architecture using the helloworld example base. Now that I am starting to develop the...
Hi,
Is it possible to check somehow if a BLE packet has been transferred (or not) from a peripheral to the central device?
Through a succesful transmission flag or something...
Hi, I'm using nrf52832 custom board and 14.2 SDK, S132.
In my program I'm using SAADC, PWM, I2C along with softdevice and PID. my device is working fine for some time but...
Hi! I've noticed that softdevice S113 is Bluetooth 5.1 compliant , and that the nrf52 family chips are Bluetooth 5.2 compatible in terms of hardware. a. Is there any target...
fds_init fails for several valid reasons, but my issue is how to recover. This for me was triggered by a firmware upgrade overwriting the fds file area. This can trigger fds_init...
Hi, I learned how to replace the softdevice for a normal application. I've replaced 140 with 340 in my app. However I don't know to do that for the boolloader.
What I want...
Hi Nordic,
I want to control an LED with the nrf GPIO, the LED Anode is connected to VDD, through a resistor, and the cathode is connected to the GPIO. Under this configuration...
I want to use the nPM1100 to battery manage, and supply power to the nRF52xxx - along with a heavy duty load ***directly across the battery***, so that full battery voltage...
Hi,
I'm running the experimental example: 'ble_nfc_pairing_reference_pca10400_s132' using sdk17.0.2 (and 17.1.0).
After I installed the micro-ecc following the guide on...
Hello
I am evaluating design of wireless communication in power supply with nRF24L01P , and I have 4 questions.
1.I want to know the Mean Time Between Fails (MTBF) and...
I'm using softdevice s140.
My power comes from a CR2032 coin cell.
My board has a 1.8V LDO (Toshiba TCR3UM) because my temperature sensor is calibrated for 1.8V (TMP112B...
