Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello Everyone,
I am a beginner for working on Nordic devices. I have one query. I have to build a firmware in NRF52840. Now 2 different apps will be connecting to this...
Hello
I am using 5 nrf52833 dev kits and the ble_zigbee_dynamic_light_bulb_eddystone example from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
I have modified the following...
I'm trying to achieve a low power operation on a device which has a nRF52833 module with a SPI peripheral on Zephyr. It is based on the peripheral_lbs.
The intended behaviour...
Hi, I am learning how to implement Long Range on the UART central and peripheral examples using SDK 17.0.0. The error I am facing is that the debug terminal shows
[ app_timer...
The provided ble_app_template10056e from nRF5_SDK_17.1.0_ddde560 crashes:
The crash was reproduced using:
1. nRF52 DK Kit - ( https://www.nordicsemi.com/eng/Products...
Hello,
Can anyone know how to print MCUboot info on serial debug terminal or Normal Debug terminal using COM port?
What are the Configurations to be added for this?...
Hi guys
I am working on a project need to pass the ADS1231 read data through BLE. But I haven't done so far. I just try to read the ADS1231 value first. Referring to some...
I see an example of a central device and peripherals as one, and I see it using the following three registers to determine the start or end of the broadcast, the beginning...
As stated in the title.
I am using nrf52832 provisioner example with light_lightness example in v4.2.0. Provisioner is able to set up the network with clients and servers...
Hi support team,
We have a new project now. We plan to use nrf52832 for the project. We know about the BLE and the related development, but we are not familiar with nordic...
I am using C++ to program the nRF52 DK and I am trying to use the standard vector library.
When I try and compile it I get the linker error:
${GCC_PATH}/arm-none-eabi...
Hi I am trying to do the led blinking in nrf52840 but the led is not even turning on i have given the code below can any body help me out.
nrf_gpio_cfg_output(14); nrf_gpio_cfg_output...
Hello,
I was able to create a mesh network with two nrf5340 boards configured with the mesh light sample and the mesh light switch sample.
I am trying to substitute...
I recently purchased a Thingy 52 with the goal of processing the the raw magnetometer, accelerometer and gyroscope data using a sensor fusion algorithm to determine orientation...
