Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I am offloading sockets in config. I instantiate a socket, set the send/recv timeouts, and then call connect(). It's returning a 95 which is EOPNOTSUPP. I was able...
Hi,
I'm investigating firmware image signing on the nrf9160 using MCUBoot and the nRF Connect SDK v17. I have configured
and it seems to work via `west build -b nrf9160dk_nrf9160ns...
Due to parts shortages, we are having to scramble to find compatible hardware for our project. I have sourced some nRF5340 modules but need to know if Gazell is supported...
Hi!!
I am facing an issue wherein more than one device is acquiring the leader role in a same thread network.
In my setup, I have a total of 4 devices. Three of them are...
Dear Team,
I have to use many number of pages to store data in flash memory in nrf52840 , but I am confuse that what will be start address and end address in flash_fstorage...
Hello Team,
I am facing segmentation fault while reading the OTP memory using pointer in my code. To write the OTP value I have used below command which was successful and...
Hi,
I received the nRF9160DK yesterday, and used the AT Client to get talking to the modem and connecting to a network. In VS Code I built an application from sample ...
Hi there,
I'm using the product specification of the nRF52840 to program the SAADC in continuous mode using its internal timer. I'm not able to use your SDK. Unfortunately...
We've built a custom board, at power off current is 1-2uA and when connected average current is ~4.7mA. Internal DCDC is enabled, this shaved off >2mA. Other than reducing...
Hi ALL:
- SDK version: nRFSDK 15.3
- HW: nRF52832
I am tried to earse the flash by sg_flash_page_erase(uint32_t page_number), but still failed. My code snippet as...
Hi there,
I want to read the memory from nRF52840,
but J-Link showed me, J-Link is defective, how can I rectify it ?
It's from 2018 J- Link ,
Screenshot :
tha...
Hello,
I'm running the nRF Mesh SDK 5.0.0 with the light CTL LC server example. I have also developed an implementation of a DALI master. DALI is a manchester encoded signal...
I am using: \examples\ble_peripheral\ble_app_uart and \examples\ble_central\ble_app_uart_c .
In Nordic infocenter it says: The application scans peripheral devices and connects...
Hello all,
I would like to know if it would be possible to simultaneously use 3 instances of I2C and 2 of I2C for the nRF5340DK. As stated in the data sheet, the application...
