Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello. At first I m newbie and don't have experience with Thingy:52 and Embedded Segger Studio for ARM.
I m trying to work with my Thingy with Segger j link and SEGGER embedded...
I am trying to build the zephyr blink project using west :
I have installed the gnu-arm-embedded toolchain and set my environment variables accordingly : ZEPHYR_TOOLCHAIN_VARIANT...
Hello
The Uart Baudrate is initiliazed at 115200 baud but i the BLE nRF52833 is sending with about 115900.
I try to switch to hf clock but the baudrate is to high.
...
Hey,
I have a nRF central that connects and bonds to peripheral devices via BLE.
From what I understand, the peripheral device has a BLE MAC address that isn't consistent...
I am setting to NRF_SDH_BLE_CENTRAL_LINK_COUNT=1 ,it is working fine for ( 1 central and 1 peripheral )connection is fine(data also sending),but i am changed to NRF_SDH_BLE_CENTRAL_LINK_COUNT...
Hi
I am new to Nordic
I am using nordic nrf52832 with segger embedded software tool woth nordic support version NRF SDK 16.0.0
I am facing issue with build configutations...
Hello.
I would like to get an event that an advertised packet has been sent in a peripheral device. Is there a way to do this? Also, is it possible to get the channel used...
I'm using nRF9160DK and in that cJSON formation give me some error because of that my device will restart again and again
as in code if I'm input cJSON_AddNumberToObject...
Using SEGGER embedded studio for ARM (Nordic Edition) v5.60. using Project-> Configure nRF Connect SDK Project Fails in configuring MCUBoot in Zephyr.
No Documentation on...
i am working on power measurement of ble. i want to change ble connection interval in nrf blinky code say to 100ms, 200ms, 1000ms. how to achieve this and
what is the use...
I"m using SLM from NCS 1.6.1.
I'm testing HTTPCREQ with HTTPC port 443 and security tag = 1. After I reset SLM, my send is successful and passes server validation checks...
I have been using the DFU on nRF5 SDK for some years now and we use this feature to update firmware in the field.
I have sucessfully managed to get the SMP Server sample...
Hello everyone!
I'm using nrf5_SDK_for_Mesh_v5.0.0_src and I'm trying to run the Serial example. I see no Bluetooth advertising so I wanted to redirect __LOG to UART.
...
