I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
This has been happening for a very long time when building nRF connect SDK applications on a windows 10 machine via the command line with cmake and ninja. In an application...
Had this linking error when I tried to build the bootloader for nrf9160dk_nrf52840 calling
west build -b nrf9160dk_nrf52840 ..
the same error ocurred using
cmake - GNinja...
I am new to this community although I have already been exposed to products with Nordic components.
I have been reading a lot and watching recorded webinars the past few...
Hi everyone,
I am trying to send a custom zigbee message by using this function zb_zcl_finish_and_send_packet_new() with a callback function to free the buffer after send...
I want to delete the bound device information through erase_bonds during the main function, but this will always cause chip errors and restart,I want to know how to solve...
Hello. I work on the multirole mode application. There is a strange situation, the conn_handle is not equal to 0 when connecting for the first time (equal to 2). Because of...
Hi. I am using nRF52840 DK as an central device to connect 6 peripheral device. There is no problem. But I want to add peripheral role to central device fo send data which...
Hi Nordic team/Everybody, I'm working with nRF52840 PCA10056 , Thread_Zigbee_ v4.1.0 , and light_control example.
I modifed, try to add T emp_measurement ZCL in Light_Bulb...
Hello, just updated from previous segger version to 5.34 but compiling an existing project
/ncs/v1.5.1/toolchain/segger_embedded_studio/lib/SEGGER_crtinit_v8m_mainline_little...
Hi
I am using the this example code nrf52-ble-app-uart-c-multilink [ https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink ]
If NRF_SDH_BLE_CENTRAL_LINK_COUNT...
Hi,
Would like to understand when will be the chip select pin be asserted and de-asserted when reading/writing a QSPI external flash?
What will enabling QSPI by setting...
Hello and to whom it may concern
I am currently using nRF51422_QFN48
with laser marking on the IC body
N51422QFAAF01616CS
i am using nRF desktop connect and try to...
Hello,
I'm having this problem with this nRF24L01+ connected to an ESP8266 (ESP12-E on BOB), and I'm using NodeMCU 2.2.1. The nRF24L01+ module I'm using is a small board...
Hello everyone,
i have a problem reading data from MAX30101 sensor FIFO. I set up the sensor and enable all 3 LEDS (Red, IR, Green), but when I read the data from the FIFO...
I'm using nRF Connect v1.5.0, Zephyr, and Segger Embedded Studio (SES) to develop an application I'm testing on nRF5340-DK.
I have a project that compiles and runs. But...
