I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi there
I mount the 19pin connector on nrf5340dk board and connect to segger j-trace pro . The debugger function work well.
Later i modify the nrf9160 etm trace project...
Has anyone had success getting triggers on motion to work with the LIS2DH? I only have INT1 wired so I modified the drivers to work on INT1 as the spec document says it should...
I'm writing software for nRF52832 using nRF5 SDK v17.0.2
I'm using a timer to create a buzz/tone using timer 3. This works as expected.
I'm also using the SAADC to measure...
I'm learning how to use OTA DFU (via BLE) now. I have Python 2 and 3, pip installed in my Win10 laptop. When I install the nrfutil with PowerShell, I had some errors (see...
I've been using the nrf connect toolchain for a bit, and after some initial trouble it was working ok, but now its randomly giving this error whenever I try to build anything...
Hi,
I am trying to convert a number from little endian to big endian. There is a built in function "NTON" that I can use instead of writing my own code, but I can not find...
I'm using two nRF52805 to get sensor values and send 2 sensor real-time values to my phone via BLE. Each nRF52805 BLE works well (Individually tested by nRF Connect App. It...
The encoders I am using generating about 500 pulses per second, and I need to read 3 of them at the same time. I assume a good approach for that is to use the hardware timer...
Hi, working with NCS v1.4.2, I see building products for an <app> landing into subfolder <app>/build/, in several flavours
app_moved_test_update.hex app_signed.hex app_test_update...
Hello,
I'm trying to flash an example code from the SDK onto the Arduino Nano 33 BLE board.
I tried to use the external debugging on an arduino nano 33 ble card but the...
Hi,
I'm using NRF52840 and having a lot of issues with hard fault.
From time to time, I get an application crash with the following log:
HARD FAULT at 0x00000000 R0...
This question may be better suited for the Zephyr forum, but I figured I would ask it here as well in case somebody can easily see what I may be missing.
I am trying to...
I am attempting to use the UART peripheral with a UART device which communicates via 1 start, 7 data, 1 even parity and 1 stop bits.
Is there any? way to configure or fake...
According to this post it seems clear that a peripheral device cannot set the connection event length in a given connection (and only has mild influence on the connection...
