Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I updated my Power Profiler software on the NRF Connect Desktop software.
Immediately after switching to the new GUI, I noticed a significant change in power performance...
I am trying to use the NRFX_WDT design in SDK 16.0.0 on a board using the nRF52832.
In the file nrfx_wdt.c, the allocation index is declared/defined as:
static uint8_t...
The drop down does not list the nrf5340dk.
Using nRF Connect Toolchain Manager I open a command prompt in the v1.5.0 sdk,
cd zephyr\samples\drivers\spi_flash
I did:...
Hello,
I have a project based on Cloud Client v1.4.0 using AWS IoT cloud as the backend. I have made some changes in the code so that I disconnect after sending some values...
The frequency tolerance for ANT stack for an external 32.768 kHz crystal oscillator should be +/- 50 ppm max.
Does it mean over temperature range?
There was the same question...
HI:
Now i am use the OTS to transmit image, if we want to set the MTU=185, how many paramter must config here?
example:
CONFIG_BT_CTLR_TX_BUFFER_SIZE=185 CONFIG_BT_CTLR_DATA_LENGTH_MAX...
Hello, I have created my own C program (in eclipse) that basically should just initialize to an LTE network and connect to it, nothing fancy at this point.
I have come across...
Hi, I tried to set up the environment for the nRF Connect SDK v1.5.0 using nRF Connect for Desktop on Ubuntu 18.04.
In step 2 (Cloning the SDK), I got some errors while...
I use arduino to program a nRF52832 board. I had problems to move a running project with a ST7789 SPI display to the nRF52832. I use the Adafruit lib to drive the display...
Hi,
My custom card has ic nrf52832QFAAE0 AND NRF52DK has ic NRF52832QFAAE1.MESH SDK EXAMPLES runs properly on NRF52DK but not working on my hardware with ic NRF52832QFAAE0...
Hi,
What cellular connectivity, the provider's DNS, and backend cloud services, invariably connecting over MQTT is transient and the internal blocking timeout of mqtt_client_tls_connect...
I'm using Zephyr on a nRF52840 and I'd like to use the QSPI with the Fat Filesystem. I added the following Config statements to prj.conf:
The nrfx QSPI driver and file...
Hello,
I am wondering where to change the baud rate for the UART in the NRFConnect SDK using zephyr. I am working with the peripheral_uart example.
Thanks,
RJ
