Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
When I plug in my NRF51 Dongle it shows up in Windows explorer as additional drive (JLINK). Can I use this medium to configure my application? Can I read a file pun...
Hi,
I have a small pcb project with low power bluetooth IC NRF52832. There is a limited space on PCB so i decided use the 2.4 GHz chip antenna. İs there recomended chip...
we have deploy the serialization libraries in our host to communicate with nrf52840, but it seems the serialization libraries don't handle pairing/bonding event, so we can...
So I am doing a number of crypto operations. One of which for example is an ECDSA signing operation. I do that through mbedtls_ecdsa_write_signature which is using the CC310...
Hello,
We're currently evaluating the feasibility for leveraging our existing NRF51840 as host/system processor that runs all of our application code and runs the BLE...
Hi,
I am having some trouble. For a project, I need GPS, 9 axis IMU (accelerometer, gyroscope, and magnetometer), a microphone, and LTE connectivity in a small form factor...
Hi Team,
I am using nRF Connect SDK v1.3.0 tag for nRF52840 DK.
I am trying to integrate BLE HCI UART project files into Zigbee light switch project.
I have attached...
SDK : nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Hardware : 2x nRF52840 (PCA10059) + 1x generic overflow sensor.
This is an attempt to gather complete information regarding...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
I am using nRF52832 as central device.
I see from sniffer that LL_VERSION_IND...
I have Power profiler kit 1 which was working fine. I have updated my nrfconnect app and since then on my power profiler kit, I am unable to perform battery power profiling...
Hi
I am trying to build the BLE Secure DFU Bootloader example using SDK 17.02 and the PCA10040 Dev board. Following various threads in the forum, I have been successful...
Hello, I'm trying to merge NFC writeable example " writable_ndef_msg " with BLE Beacon " ble_app_beacon ". My aim is to start BLE Beacon after the scanning of NFC. I have...
Hi.
I have implemented the Central and Peripheral NUS service on two devices(nRF52). Since the central knows the characteristic values, I would like to bypass service discovery...
Hi, I've a timer configured by gpiote to capture with a second 'overflow' capture should the signal stop. I'm not using an interrupt instead the CC[0] value is being used...
