I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I am able to send AT command to modem using AT command interface API.
Is it like there is no AT command to send the data to http server? I am referring nrf91_at_commands_v1...
Hello, It is my first pcb with a rf-antenna. I have read some articles about the topic an came up with the following inverted f-antenna design ( ti inverted f-antenna ). ...
Hi,
Out of several Thingies 91 that we programmed with our software and security keys/tags two of them that had their battery drained seem to have lost their security tags...
HI,
If I insert in the main loop ( in the connection branch ) the instruction "idle_state_handle();"
for (;;) { if (flag_connected==0) { idle_state_handle(); } else {...
It appears that when the Dongle originally ships the Bluetooth advertiser is switched off.
ok i understand to download all kinds of software or some kinds of it to turn...
Hi all,
When I use the Bluez tool meshctl on Jetson nano(ubuntu arm64) to provision a nRF52832 device, failed at the authentication step, as follow:
the 16 octets keys...
Hi,
I am developing a mobile application using React Native for interfacing, configuring and doing FOTA over BLE. I want to know if you provide any BLE or FOTA libraries...
I'm trying to find the UUID for the 'Time Second 32' characteristic described in the GSS v2 available here , but I can't find it in the Bluetooth Assigned Numbers document...
I browsed the Infocenter and found 'lots' of information and the instruction to install nRF Connect so I did. I hadn't decided which DK I needed to do what I wanted so when...
I continue to be confused by the Nordic setup of projects. There are a bunch of different demos, but what if you want to compile features from different ones?
Specifically...
Hi ,
I have used Calendar example running on RTC2 for my timing feature .
Below are the initializations for starting RTC2 for my clock .
#define CAL_RTC NRF_RTC2 #define...
Thanks in advanced. Both platforms are: nrf52832, sdk17.0.2. The peripheral is based on ble_app_gls and I set static passkey 123456, the central is based on ble_app_hrs_c...
HW: nRF9160 DK
SDK: nRF Connect SDK v 1.4.2
Hello, this is to report a buggy behavior I encountered when trying to implement a BLE-LTE gateway on nRF9160 DK
First...
I want to move the UART on thingy91:nRF9160.
prj_thingy91_nrf9160ns.conf added the following two line.
CONFIG_UART_ASYNC_API=y CONFIG_NRFX_UARTE0=y
The asset_tracker...
Hi All,
I want to use DFU to update the firmware from central to peripheral over BLE , both central master and peripheral are nrf52840.
Central master can find unknown...
