I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I want to use BSDLIB in my application. According to documentation ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrfxlib/bsdlib/doc/ug_bsdlib_porting_os...
I've developed a little test application on a nrf52832 chip to run fstorage in a bootloader memory address. I followed the nordic guidance to set up, build, and install a...
Hello, The card has already been assigned to an NRF Cloud account. However, we wanted to change the account card for a practical reason. We have therefore deleted the card...
I tried using nrf52832(as slave) communicate with stm32, it successed .
But when I changed nrf52832 to nrf52840 to do the same thing, it failed .
I use the nRF5_SDK_15...
Hello there, I following the nRF IoT SDK getting started and after Connecting Devices to Router section I succeed in connecting devices to router.
After that, I edited...
Dear Nordic Team,
I was trying to understand event handlers from SDK5 examples. I understood that by using following macro we can register our event handlers, and afterwards...
Hi, I'm trying to run the JLink debugger using Ozone to debug my program. When I run nrf_crypto_init(), I encounter a hard-fault. The program is not experiencing any problem...
Hi,
I am trying to develop an application on nRF52840 development kit board. When I am trying to build I am getting below error "nrfx.h: No such file or directory". For...
I am trying to port BLE_APP_Interactive to nRF52840 as I require 2 uarts in my application and larger memory. I realise I need to change the crypto to CC310, and I have followed...
I've been seeing issues with getting an interrupt on the TX side. I reckon it could also be linked to the RX module cause if the payload isn't sent, the interrupt on the TX...
Hi,
I have implemented a custom bootloader/firmware package, but have recently been running into issues when integrating the two. I have found in some instances when using...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
When trying to build/run the btle throughput demo I get a device not supported error.
When looking in the Options - Device settings for
the project the Software Packs...
Hi All,
the logging output (NRF_LOG_...) in the SDK17 via the UART works fine on the DK board (only change from the HRS example was the NRF_LOG_BACKEND_UART_TX_PIN has been...
