Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi everyone,
I want instead of MAC address to advertise my device using its 64bit unique ID. What I am considering, is to use the p_data array for that purpose and more...
Hi, I see an interesting situation.
I got flash corruption with values 0xff after random power cycling and it's happened only if I have flashed the bootloader
soft device:s132
sdk:15.3.0
I implemented the following, but the event does not occur even if the voltage is V2.8 or less.
Do you know the reason?
===
NRF_SDH_SOC_OBSERVER...
The nRF5 SDK's throughput sample (ble_app_throughput) provided very convenient shell commands to configure key parameters affecting throughput in a connection, such as ATT...
Hello,
in my project I have a custom board with a nRF52832 chip, which reads 4 channels with a sample rate of 1kHz (1ms). The SAADC readings get transmitted to a nRF52840DK...
soft device:s132 sdk:15.3.0 board:nRF52832 board (taiyo yuden EYSHCNZWZ)
Unable to receive event 'NRF_EVT_POWER_FAILURE_WARNING' I implemented the following, but the event...
Hello
Using the timer, I am making code that turns on LED1 to 3 sequentially. I thought it was going to be very simple, but it's not going as well as I thought.
I'm making...
Hi, I have very STRANG issues. I am adding custom Characteristics to custom Services. I have added 10 custom Characteristics with the same config 8 of them are working perfectly...
Hi,
I am on ncs master branch, when i build and load the Serial LTE Modem(SLM) application the application struck at mcuboot
The only additional configuration option i...
I am using nrf52840 board. I hvae interfaced a gsm module(quectel m66).The problem is my device gets an APP_UART_FIFO_ERROR after every few sms commands.The maximum data i...
Hello everyone!
I have an issue about upgrading firmware over Bluetooth LE with a mandatory pairing of devices. I want only paired devices to have the ability to upgrade...
hello,
In the nrf51822 sdk 5.1 I can see a routine named ble_app_ibeacon.
I find a parameter define as below,the data is added to the advertising data.
#define APP_MEASURED_RSSI...
Hello,
Our team has narrowed down a particularly interesting issue with the boot sequence / initialization of our BMD-341 chip, which itself runs the nRF52840 SoC. For context...
Hi , i am using the nRF52DK and i have a small problem with the pwm driver.
i basically would like that the frequency increases if i press a button or decreases if I press...
