hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I tried with the DK and my own USB-serial adapter and both fails at 1M with HWFC with this error:
nrfutil dfu serial -pkg bltest.zip --baud-rate 1000000 --flow-control 1...
Hi I would like to interface the nrf9160 with amw136 (silicon labs) module wifi.
The amw136 has the interfaces: serial (UART, remote terminal), SoftAP and WLAN client (concurrent...
i am working on nrf52832 DK, i am trying to upgrade my development kit firmware using mobile
and i successfully build "secure_bootloader_ble_s132_pca10040.hex " application...
I'm currently using this setup on a fitness device prototype that will send battery status, scores and relevant infos. RPi >>>RFM69 915MHz )))))) ((((( RFM69 >>> Adafruit...
Hi,
I am using the softblink library in SDK 13.1 to control a RGB status indicator LED. It works fine, until I want to change the PWM settings or the LED pin.
The change...
I'm developing an interface I2C to one sensor including SCL, SDA and open-drain return to know if
the sensor is ready to work. After Reset by "Build and Run" form Segger...
Hi,
I'm a new guy for the development in nRF52840 and try to build the application by using 802.15.4. I have two questions, as follows:
Firstly, when I follow the instruction...
Hi, environment is nRF5_SDK_16.0.0_98a08e2 windows SES target is nrf52840. I am using the nordic dev board. The final product is a wearable, which will connect to a smartphone...
Hi All,
I'm using NRF52832 for our product. I test bootloader functionalities with development kit. The software system is also tested separately by directly programming...
Is it possible to achieve 2Mbps real speed when sending 2Mbs of data in BLE.50?
It supports USB 2.0 H / W, but the actual speed is full speed. Is high speed possible with...
What is the need for a provisioner? Is it mandatory to have provisioner while client and server communication? In which condition provisioner needed in mesh network? Which...
Hello,
This is more a question than a issue. I am working on a sample to transmit data from MOSI of the SPI to UDP. It is possible to see received data through SPI on LTE...
I would like to make a timer to check the GPIO status.
The current code is like below:
I already checked that timer function is worked by implant the specific event...
Hi, I am developing sensor reading via ble using nRF52 Development Kit from scratch.
Since bluetooth, nrf, sdk stuff are a whole new world for me, I m following step by...
