We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I would like to use PCA10031 to be a sniffer. It can't update and show as below figure.
I've also refer to discussion as below website to turn it into BOOTLOADER...
Hi,
I am using NRF52832 and SDK 11
I tried to include DFU function into the device. I merged bootloader (from modified bootloader example), application, softdevice into...
Hi,
Since migrating to V1 of modem firmware and tag v1.0.0 the low power mode of the SIP is back up to about 700uA again instead of the 7uA we were seeing before upgrading...
Hi,
I have some problems with the example 'timer' and 'simple_timer' provided with sdk_15.3 (which are explained in my other ticket). So can I have an example which works...
what exactly ble_beacon stack is used for? what it does and can it be used to advertise or send user data (like string) and receive notifications from other devices ...can...
Im struck at some point with some error, added all supporting file along with header files but still im getting error. Im using sdk15.3 pca10040 nrf52832.
please verify...
I have a NRF51 DK board, and can't get it to do anything with BLE (probably including any of the examples that require a softdevice) but I ran the blinky examples just fine...
I am using a ultra-miniature (BMD-350) series module from Rigdo which has the nRF52832 BLE SoC. It is placed on a custom board such that all pins from the nrf52 SoC are brought...
Hi,
My projects with Nordic chips thus far have been pretty simple, but now I would like to use an RTOS. My question is, do I use the FreeRTOS available in nRF SDK, or move...
Hi,
I have a problem with understanding, how bits in ble_gatt_char_props_t are related with Specification of the Bluetooth System v5.1 Table 3.5: Characteristic Properties...
If I use a breakaway for some debug pads which SWDIO and SWDCLK are connected to and then snap it off so the traces are no longer connected to anything, will this cause a...
I'm trying to run the https://github.com/NordicPlayground/nRF52-ble-long-range-demo on Fanstel modules with integrated AFE by Skyworks - BT840X(E) https://www.fanstel.com...
I'm trying to connect to an AWS MQTT broker I have set up based on the code in https://github.com/joakimtoe/fw-nrfconnect-nrf/tree/36532a8ca60bf7139a988b5cbb4e6cb47948a9fa...
Hello In this thread we discussed a possability of building a system with large number of conecctions. So, we need to get data from 30 peripheral nodes on one central host...
Hi,
I'm developing a product that should take an image of a low-resolution image sensor, process it and send the result via BLE.
The camera has an 8-bit parallel interface...
