Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello all !
So here is my problem, I have a computer as a CoAP client running the Python script from : https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
i use a 52832 module scan BLE advertisement signal, and found it can recived lowest DB value is -92db. but i use my Phone to scan same advertisement signal, it can recived...
Hi
I am using the nrf52832 DK for my project.
Using ble i need to establish wireless connection b/w the android phone and the board.
I need to send data from the phone...
During manufacturing verification we want to run some tests that will require us to talk to our custom nRF52840 device over bluetooth.
The ideal solution for us would be...
Hi
In the infocenter, I can find the important note which says, that to run nRF5 SDK for Mesh v2.2.0 on an nRF52832, nRF5 SDK 15.0.0 as well as the softdevice S132 v5...
The scratchpad is overflowing when generating a keystream prior to a CCM decrypt operation.
The size of the scratchpad is calculated according to the formula in the product...
is there any tutorial that shows me how to read data from the BLE using android. My NRF 52840 is connect to my device(Which is i expected data to read from) i am able to send...
To the kind attention of Nordic,
while I'm planning to do a software porting from nRF24 to nRF52840, I've been studying some of the usb applications you provide in your...
Hi,
I am a newbie with zigbee on nRF52840.
I have tried serveral days with zigbee SDK but have troubles to work.
Finally i have found that example zigbee/light_control...
Hello!
We have nRF52832 chip on our product and we have some problem with one of its IOs.. We configured P0.16 as RX of UART, And when we run it we see this behavior of...
my example project: wireless_uart_raw_first_pca10056
chip : nrf52840.
i want to make my application timer in the my example project. time tick is 100 msec. in every 100...
Is it possible to get the Build Type from the Factory information configuration registers (FICR)?
From https://infocenter.nordicsemi.com/topic/comp_matrix_nrf52832/COMP...
Hi
I have some question about OTA .
1.The nRF SDK hvae twos way for OTA: single bank and dual bank;The nRF Mesh 3.10 too?Because my firmware maybe very large,so I want...
Dear all,
I am having issues with service discovery of two primary services ( Battery and one propriotary based on NUS) I am currently using SDK 14.2 on NRF52832 chip running...
Hi, I'm trying to use the Seggar Embedded Studio to debug my code, but the Seggar Embedded Studio can only recognize the nRF52840 development board, not the external device...
